MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 21 Mcqs, each offering curated multiple-choice questions to sharpen your Technical Drawing knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Single-line drawings show the centerline of the pipe. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 2. |
When dimensioning piping drawings, it is not necessary to indicate the size of each pipe. |
| A. | 1 |
| B. | |
| Answer» C. | |
| 3. |
Copper tubing is not suitable for process work, for plumbing, or heating systems. |
| A. | 1 |
| B. | |
| Answer» C. | |
| 4. |
In a developed piping drawing, horizontal pipes may be revolved into the vertical plane so the entire installation can be shown on one plane. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 5. |
Brass and copper pipe is used in plumbing for supply, soil, waste, drain, and vent lines. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 6. |
Axonometric drawings are seldom used in piping drawings. |
| A. | 1 |
| B. | |
| Answer» C. | |
| 7. |
Copper pipe is brittle, and settling can cause fracture unless the joints are sufficiently flexible. |
| A. | 1 |
| B. | |
| Answer» C. | |
| 8. |
Valves are used to stop or regulate the flow of fluids in a pipeline. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 9. |
This type of pipe is commonly used for water or gas service, and also as soil pipe: |
| A. | PVC |
| B. | Copper |
| C. | Steel |
| D. | Cast-iron |
| Answer» E. | |
| 10. |
A wide variety of plastic pipe, both rigid and flexible, is used in construction. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 11. |
Brass and copper pipe should be joined with fittings of copper-base alloy to avoid corrosion. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 12. |
Joints between pipes, fittings, and valves may be screwed or flanged but not welded or soldered. |
| A. | 1 |
| B. | |
| C. | 1 |
| D. | |
| Answer» C. 1 | |
| 13. |
Plastic pipe is lightweight and corrosionproof, but typically is not resistant to chemicals. |
| A. | 1 |
| B. | |
| C. | 1 |
| D. | |
| Answer» C. 1 | |
| 14. |
PVC joints are made with flared joints or solder joints. |
| A. | 1 |
| B. | |
| Answer» C. | |
| 15. |
This type of drawing shows two lines representing the pipe diameter: |
| A. | Single-line |
| B. | Double-line |
| C. | Standard piping |
| D. | Centerline piping |
| Answer» C. Standard piping | |
| 16. |
Piping may also be shown in orthographic projection. |
| A. | 1 |
| B. | |
| C. | 1 |
| D. | |
| Answer» B. | |
| 17. |
This is used in applications for nonferrous construction: |
| A. | Copper tubing |
| B. | Steel pipe |
| C. | PVC pipe |
| D. | Iron tubing |
| Answer» B. Steel pipe | |
| 18. |
When dimensioning piping drawings, you give the lengths of all runs of this type: |
| A. | Straight |
| B. | Angular |
| C. | Filleted |
| D. | Transverse |
| Answer» B. Angular | |
| 19. |
In this type of drawing, vertical pipes may be revolved into the horizontal plane: |
| A. | Standard view |
| B. | Elevation view |
| C. | Transverse piping |
| D. | Developed piping |
| Answer» E. | |
| 20. |
These types of pipes are generally connected with bell and spigot joints or flanged joints: |
| A. | Soil and waste |
| B. | Water and gas |
| C. | Water and steam |
| D. | Gas and soil |
| Answer» C. Water and steam | |
| 21. |
This type of pipe is commonly used for water, steam, oil, and gas: |
| A. | Wrought iron or copper |
| B. | PVC or steel |
| C. | Steel or wrought iron |
| D. | Copper or PVC |
| Answer» D. Copper or PVC | |