MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 19 Mcqs, each offering curated multiple-choice questions to sharpen your Technical Drawing knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Knurl is a pattern form on a surface to provide for better gripping or more surface area for attachment. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 2. |
It is not always possible to show all of the drawing views in alignment on a sheet. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 3. |
A lug is a flattened collar or rim around a cylindrical part to allow for attachment. |
| A. | 1 |
| B. | |
| Answer» C. | |
| 4. |
A boss is a short raised protrusion above the surface of a part. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 5. |
Simplified conventional representations that deviate from true orthographic projection may be used to enhance economy and clarity in a drawing. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 6. |
A counterbore is a cylindrical recess around a hole, usually to receive a bolt head or nut. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 7. |
Small curves called runouts are used to represent fillets that connect with plane surfaces tangent to cylinders. |
| A. | 1 |
| B. | |
| Answer» B. | |
| 8. |
A keyway is a small groove cut around the diameter of a cylinder, often where it changes diameter. |
| A. | 1 |
| B. | |
| Answer» C. | |
| 9. |
Right-hand and left-hand parts are mirror images and are made to be interchangeable. |
| A. | 1 |
| B. | |
| Answer» C. | |
| 10. |
A plane surface cannot intersect or be tangent to a contoured surface. |
| A. | 1 |
| B. | |
| Answer» C. | |
| 11. |
When a curved surface intersects a plane surface, an edge is formed. |
| A. | 1 |
| B. | |
| C. | 1 |
| D. | |
| Answer» B. | |
| 12. |
A fillet is a rounded exterior blend between surfaces. |
| A. | 1 |
| B. | |
| C. | 1 |
| D. | |
| Answer» C. 1 | |
| 13. |
If a plane intersects a contoured surface, no line is drawn to represent the edge. |
| A. | 1 |
| B. | |
| C. | 1 |
| D. | |
| Answer» C. 1 | |
| 14. |
This is a hollow cylinder that is often used as a protective sleeve or guide or as a bearing: |
| A. | Lug |
| B. | Bushing |
| C. | Chamfer |
| D. | Knurl |
| Answer» C. Chamfer | |
| 15. |
This is an angled surface used on cylinders to make them easier to handle: |
| A. | Fillet |
| B. | Taper |
| C. | Chamfer |
| D. | Lug |
| Answer» D. Lug | |
| 16. |
This is a flat or rounded tab protruding from a surface, usually to provide a method for attachment: |
| A. | Lug |
| B. | Boss |
| C. | Chamfer |
| D. | Spotface |
| Answer» B. Boss | |
| 17. |
This is a rounded exterior blend between surfaces: |
| A. | Fillet |
| B. | Round |
| C. | Taper |
| D. | Chamfer |
| Answer» C. Taper | |
| 18. |
These are used to attach parts to a cylinder so they won't turn on it: |
| A. | Lugs and bearings |
| B. | Keyseats and bearings |
| C. | Knurls and keys |
| D. | Keys and keyways/keyseats |
| Answer» E. | |
| 19. |
This is a conical-shaped recess around a hole, often used to receive a tapered screw head: |
| A. | Boss |
| B. | Spotface |
| C. | Counterbore |
| D. | Countersink |
| Answer» E. | |