MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 14 Mcqs, each offering curated multiple-choice questions to sharpen your Machine Kinematics knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Following are the specifications of a single purchase crab:Diameter of load drum, d = 200 mmLength of lever, l = 1.2 mNo. of teeth on pinion, T1 = 10No. of teeth on spur wheel, T2 = 100On this machine efforts of 100 N and 160 N are required to lift the loads of 3000 N and 9000 N respectively. Find the efficiency at 9000N. |
| A. | 30 % |
| B. | 40 % |
| C. | 46.8 % |
| D. | 56.8 % |
| Answer» E. | |
| 2. |
Following are the specifications of a single purchase crab:Diameter of load drum, d = 200 mmLength of lever, l = 1.2 mNo. of teeth on pinion, T1 = 10No. of teeth on spur wheel, T2 = 100On this machine efforts of 100 N and 160 N are required to lift the loads of 3000 N and 9000 N respectively. Find the efficiency at 3000N. |
| A. | 10 % |
| B. | 15 % |
| C. | 20 % |
| D. | 25 % |
| Answer» E. | |
| 3. |
On a machine efforts of 100 N and 160 N are required to lift the loads of 3000 N and 9000 N respectively. Find the law of the machine. |
| A. | P = 1/100W + 60 |
| B. | P = 1/100W + 70 |
| C. | P = 1/100W + 80 |
| D. | P = 1/100W + 90 |
| Answer» D. P = 1/100W + 90 | |
| 4. |
Following are the specifications of a single purchase crab:Diameter of load drum, d = 200 mmLength of lever, l = 1.2 mNo. of teeth on pinion, T1 = 10No. of teeth on spur wheel, T2 = 100Find the velocity ratio of this machine. |
| A. | 100 |
| B. | 110 |
| C. | 120 |
| D. | 130 |
| Answer» D. 130 | |
| 5. |
The lengths of the links of a 4- bar linkage with revolute pairs only are p,q,r and s units. Given that p < q < r < s and s+p < q+r which of these links should be the fixed one, for obtaining a ‘double crank’ mechanism? |
| A. | ink of length p |
| B. | link of length q |
| C. | link of length r |
| D. | link of length s |
| Answer» B. link of length q | |
| 6. |
ON_A_MACHINE_EFFORTS_OF_100_N_AND_160_N_ARE_REQUIRED_TO_LIFT_THE_LOADS_OF_3000_N_AND_9000_N_RESPECTIVELY._FIND_THE_LAW_OF_THE_MACHINE.?$ |
| A. | P = 1/100W + 60 |
| B. | P = 1/100W + 70 |
| C. | P = 1/100W + 80 |
| D. | P = 1/100W + 90 |
| Answer» D. P = 1/100W + 90 | |
| 7. |
A weston differential pulley block consists of a lower block and upper block. The upper block has two cogged grooves, one of which has a radius of 150 mm and the other a radius of 125 mm. If the efficiency of the machine is 50% calculate the effort required to raise a load of 1.5 kN. |
| A. | 250 N |
| B. | 300 N |
| C. | 350 N |
| D. | 400 N |
| Answer» B. 300 N | |
| 8. |
The number of links in a planer mechanism with revolute joints having 10 instantaneous centres is |
| A. | 3 |
| B. | 4 |
| C. | 5 |
| D. | 6 |
| Answer» D. 6 | |
| 9. |
It is planned to construct a four-bar mechanism ABCD with length AB= 60mm, BC = 100mm, CD = 70 mm and fixed link AD = 200 mm. If at least one link is required to have a complete rotation, this mechanism is |
| A. | of crank-rocker type |
| B. | of double-crank type |
| C. | of double rocker type |
| D. | impossible to construct |
| Answer» D. impossible to construct | |
| 10. |
For the same crank length and uniform angular velocity of the crank in an offset slider crank mechanism, if the connecting rod length is increased by 1.5 times, the velocity of piston will |
| A. | remain unchanged |
| B. | increase 1.5 times |
| C. | decrease by 1.5 times |
| D. | increase by 1.5‚àö2 times |
| Answer» D. increase by 1.5‚Äö√Ñ√∂‚àö‚Ć‚àö‚àÇ2 times | |
| 11. |
In a single link robotic arm the end-effector slides upward along the link with a velocity of 0.5 m/s while the link rotates about revolute joint with an angular speed of 1 rad/sec. When the end-effector is at a distance of 1 m from the joint, the acceleration experienced by the end-effector will be |
| A. | 1 m/s<sup>2</sup> |
| B. | 1.41 m/s<sup>2</sup> |
| C. | 1.71 m/<sup>2</sup> |
| D. | 2 m/<sup>2</sup> |
| Answer» B. 1.41 m/s<sup>2</sup> | |
| 12. |
In a slider-crank mechanism, the crank is rotating with an angular velocity of 20 rad/s in counterclockwise direction. At the instant when the crank is perpendicular to the direction of the piston movement, velocity of the piston is 2 m/s. Radius of the crank is |
| A. | 100 cm |
| B. | 10 cm |
| C. | 1 cm |
| D. | 0.1 cm |
| Answer» C. 1 cm | |
| 13. |
For a four-bar linkage in toggle position, the value of mechanical advantage is |
| A. | 0.0 |
| B. | 0.5 |
| C. | 1.0 |
| D. | ‚àû |
| Answer» E. | |
| 14. |
The lengths of the links of a 4- bar linkage with revolute pairs only are p,q,r and s units. Given that p < q < r < s and s+p < q+r which of these links should be the fixed one, for obtaining a ‘double crank’ mechanism? |
| A. | ink of length p |
| B. | link of length q |
| C. | link of length r |
| D. | link of length s |
| Answer» B. link of length q | |