730 + Mcqs in Technical Drawing Page 3 McqOptions

101.	This type of axonometric drawing has equal foreshortening along two axis directions and a different amount on the third axis:
A.	Dimetric
B.	Multiview
C.	Isometric
D.	Trimetric
Answer» B. Multiview

Discussion

102.	These weld symbols have no arrow-side or other-side significance:
A.	Projection or seam weld
B.	Back or backing weld
C.	Surface or groove weld
D.	Flash and upset weld
Answer» E.

Discussion

103.	In these drawings it is necessary to show cut surfaces and distinguish between adjacent parts:
A.	Auxiliary drawings
B.	Assembly sections
C.	3D assemblies
D.	Parts lists
Answer» C. 3D assemblies

Discussion

104.	These drawings are given to contractors to perform work or manufacture individual parts:
A.	Assembly details
B.	3D drawings
C.	Working drawings
D.	Skeleton assemblies
Answer» D. Skeleton assemblies

Discussion

105.	This should show what changes were made, when, and by whom:
A.	Portable document
B.	Record of revisions
C.	Title form
D.	Revision drawings
Answer» C. Title form

Discussion

106.	Some of the common terms used to describe technical drawing include:
A.	Drafting
B.	Engineering Graphics
C.	Engineering Drawing
D.	All of the above
Answer» E.

Discussion

107.	The View toolbar will position the view of the 3-D solid toward the ________.
A.	front
B.	left side
C.	SE isometric
D.	all of the above
Answer» E.

Discussion

108.	The default position of the UCS icon is positioned at ________ on the AutoCAD grid.
A.	0,0,0
B.	10,10,10
C.	20,20,20
D.	None of the above
Answer» B. 10,10,10

Discussion

109.	Developing the foundation plan is probably the starting point for creating a set of architectural plans.
A.	True
B.	False
Answer» C.

Discussion

110.	A typical set of architectural working drawings would probably include floor plans, foundation plans, elevations, section details, and roof framing plans.
A.	True
B.	False
Answer» B. False

Discussion

111.	AutoCAD's Design Center is used to manage various block libraries used in architectural drawings.
A.	True
B.	False
Answer» B. False

Discussion

112.	Elevation views generally include the front, right side, back, and left side views.
A.	True
B.	False
Answer» B. False

Discussion

113.	Blocks are not an important element of architectural drawings.
A.	True
B.	False
Answer» C.

Discussion

114.	The floor plan is a bird's eye view of the house.
A.	True
B.	False
Answer» B. False

Discussion

115.	If the roof pitch for a house is identified as 5/12 the height of the roof rises 2 " for every 14" of horizontal run.
A.	True
B.	False
Answer» C.

Discussion

116.	A set of working drawings used to build a house is considered a legal document.
A.	True
B.	False
Answer» B. False

Discussion

117.	Although the drafter creates the working drawings, the accuracy of the set of drawings is most often the responsibility of the design architect.
A.	True
B.	False
Answer» B. False

Discussion

118.	The top, front, and bottom views align in this manner:
A.	Horizontally
B.	Vertically
C.	According to the planar views
D.	Parallel to the frontal plane
Answer» C. According to the planar views

Discussion

119.	The organized and orderly approach to solving problems is known as the:
A.	Engineering process
B.	Design process
C.	Aesthetic process
D.	Functional process
Answer» C. Aesthetic process

Discussion

120.	The section view drawing in which one fourth of an object has been marked for removal is known as a ________ section.
A.	full
B.	half
C.	quarter
D.	none of the above
Answer» C. quarter

Discussion

121.	Scale is stated as a ratio of the number of drawing units to the number of actual units.
A.	True
B.	False
Answer» B. False

Discussion

122.	Students can complete an associate's degree in drafting which normally takes about ________ years to complete.
A.	one
B.	two
C.	three
D.	four
Answer» C. three

Discussion

123.	The Cutting Plane line reveals the type of material that the object is to be made from.
A.	True
B.	False
Answer» C.

Discussion

124.	A section-lined area is always completely bounded by a visible outline.
A.	True
B.	False
Answer» B. False

Discussion

125.	Specific tolerances are based on the part's function and fit.
A.	True
B.	False
Answer» B. False

Discussion

126.	Isometric drawings are often used by ________ to help illustrate complex designs.
A.	mechanical engineers
B.	piping drafters
C.	aerospace engineers
D.	all of the above
Answer» E.

Discussion

127.	When a finished part is measured, it may vary slightly from the exact dimension specified.
A.	True
B.	False
Answer» B. False

Discussion

128.	These are accurately drawn maps of cities and towns showing property lines and other features that control property ownership:
A.	Monument maps
B.	Cadastral maps
C.	City maps
D.	Topographic maps
Answer» C. City maps

Discussion

129.	The Offset command can be used on vertical lines but not on horizontal lines.
A.	True
B.	False
Answer» B. False

Discussion

130.	When inserting a block into a drawing the drafter can easily change the scale to match a particular scale factor for the drawing.
A.	True
B.	False
Answer» B. False

Discussion

131.	BOM stands for Bill of Materials.
A.	True
B.	False
Answer» B. False

Discussion

132.	Mechanical drafters can revise any drawing at any time without tracking those changes.
A.	True
B.	False
Answer» C.

Discussion

133.	The symbols used on electrical plans represent the standard equipment used in homes and commercial buildings.
A.	True
B.	False
Answer» B. False

Discussion

134.	An accurate record of changes made to released drawings is tracked via this:
A.	A revision block
B.	The basic title form
C.	Working drawings
D.	Portable documents
Answer» B. The basic title form

Discussion

135.	Nonisometric lines are equally foreshortened.
A.	True
B.	False
Answer» C.

Discussion

136.	Only vertical lines behind the picture plane are foreshortened.
A.	True
B.	False
Answer» C.

Discussion

137.	The first step in creating a traditional technical drawing is to ________.
A.	draw a series of guide lines
B.	set up the miter line
C.	align the paper so that it will be positioned square to the parallel bar
D.	sharpen the leads in the technical pens
Answer» D. sharpen the leads in the technical pens

Discussion

138.	Drafters are often expected to follow the drafting standards as set in the ASME Y14.5M-1994 publication.
A.	True
B.	False
Answer» B. False

Discussion

139.	The angle of revolution should always be less than 45 degrees for an aligned section.
A.	True
B.	False
Answer» C.

Discussion

140.	The bearing of a line is its angle from magnetic south.
A.	True
B.	False
Answer» C.

Discussion

141.	Several of the tools used in traditional drafting include the following:
A.	Parallel straight edge
B.	45 degree triangle
C.	Circle template
D.	All of the above
Answer» E.

Discussion

142.	Before starting an isometric drawing in AutoCAD the drafter needs to ________.
A.	set the grid to isometric
B.	set the current layer to Defpoints
C.	turn Object Snap off
D.	turn Ortho off
Answer» B. set the current layer to Defpoints

Discussion

143.	An isometric drawing is a type of technical drawing used to illustrate a mechanical part in true 3-dimensional form.
A.	True
B.	False
Answer» C.

Discussion

144.	Problem identification has to do with the final stages in the mechanical design process.
A.	True
B.	False
Answer» C.

Discussion

145.	The Press-Pull tool will ________ the face of a solid model in the direction it faces.
A.	taper
B.	extrude
C.	spiral
D.	none of the above
Answer» C. spiral

Discussion

146.	Traditionally, design and manufacturing activities have taken place in sequential order.
A.	True
B.	False
Answer» B. False

Discussion

147.	Connecting lines for conductors are typically drawn horizontally or vertically to minimize bends and crossovers.
A.	True
B.	False
Answer» B. False

Discussion

148.	Isometric drawings have equal foreshortening along each of the three axis directions.
A.	True
B.	False
Answer» B. False

Discussion

149.	Nautical maps and charts show prominent landmarks used for air navigators.
A.	True
B.	False
Answer» C.

Discussion

150.	Terminals or leads are frequently identified by colors or symbols, which should be indicated on the diagram.
A.	True
B.	False
Answer» B. False

Discussion

Explore topic-wise MCQs in Engineering.

This type of axonometric drawing has equal foreshortening along two axis directions and a different amount on the third axis:

These weld symbols have no arrow-side or other-side significance:

In these drawings it is necessary to show cut surfaces and distinguish between adjacent parts:

These drawings are given to contractors to perform work or manufacture individual parts:

This should show what changes were made, when, and by whom:

Some of the common terms used to describe technical drawing include:

The View toolbar will position the view of the 3-D solid toward the ________.

The default position of the UCS icon is positioned at ________ on the AutoCAD grid.

Developing the foundation plan is probably the starting point for creating a set of architectural plans.

A typical set of architectural working drawings would probably include floor plans, foundation plans, elevations, section details, and roof framing plans.

AutoCAD's Design Center is used to manage various block libraries used in architectural drawings.

Elevation views generally include the front, right side, back, and left side views.

Blocks are not an important element of architectural drawings.

The floor plan is a bird's eye view of the house.

If the roof pitch for a house is identified as 5/12 the height of the roof rises 2 " for every 14" of horizontal run.

A set of working drawings used to build a house is considered a legal document.

Although the drafter creates the working drawings, the accuracy of the set of drawings is most often the responsibility of the design architect.

The top, front, and bottom views align in this manner:

The organized and orderly approach to solving problems is known as the:

The section view drawing in which one fourth of an object has been marked for removal is known as a ________ section.

Scale is stated as a ratio of the number of drawing units to the number of actual units.

Students can complete an associate's degree in drafting which normally takes about ________ years to complete.

The Cutting Plane line reveals the type of material that the object is to be made from.

A section-lined area is always completely bounded by a visible outline.

Specific tolerances are based on the part's function and fit.

Isometric drawings are often used by ________ to help illustrate complex designs.

When a finished part is measured, it may vary slightly from the exact dimension specified.

These are accurately drawn maps of cities and towns showing property lines and other features that control property ownership:

The Offset command can be used on vertical lines but not on horizontal lines.

When inserting a block into a drawing the drafter can easily change the scale to match a particular scale factor for the drawing.

BOM stands for Bill of Materials.

Mechanical drafters can revise any drawing at any time without tracking those changes.

The symbols used on electrical plans represent the standard equipment used in homes and commercial buildings.

An accurate record of changes made to released drawings is tracked via this:

Nonisometric lines are equally foreshortened.

Only vertical lines behind the picture plane are foreshortened.

The first step in creating a traditional technical drawing is to ________.

Drafters are often expected to follow the drafting standards as set in the ASME Y14.5M-1994 publication.

The angle of revolution should always be less than 45 degrees for an aligned section.

The bearing of a line is its angle from magnetic south.

Several of the tools used in traditional drafting include the following:

Before starting an isometric drawing in AutoCAD the drafter needs to ________.

An isometric drawing is a type of technical drawing used to illustrate a mechanical part in true 3-dimensional form.

Problem identification has to do with the final stages in the mechanical design process.

The Press-Pull tool will ________ the face of a solid model in the direction it faces.

Traditionally, design and manufacturing activities have taken place in sequential order.

Connecting lines for conductors are typically drawn horizontally or vertically to minimize bends and crossovers.

Isometric drawings have equal foreshortening along each of the three axis directions.

Nautical maps and charts show prominent landmarks used for air navigators.

Terminals or leads are frequently identified by colors or symbols, which should be indicated on the diagram.