MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 12 Mcqs, each offering curated multiple-choice questions to sharpen your Design Steel Structures knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Rivets in group subjected to direct loads share load ________ |
| A. | equally |
| B. | unequally |
| C. | according to rivet diameter |
| D. | rivets are not used in groups |
| Answer» B. unequally | |
| 2. |
Which of the following assumption is true for rivet connection? |
| A. | friction between plates is considered |
| B. | distribution of direct stress on portions of plates between rivet holes is uniform |
| C. | bending stresses are considered |
| D. | shear stress is not uniform on cross section of rivet |
| Answer» C. bending stresses are considered | |
| 3. |
Tolerance on length for rivet diameter > 16mm is_____ |
| A. | 1.5mm |
| B. | 2mm |
| C. | 5mm |
| D. | 3mm |
| Answer» E. | |
| 4. |
WHICH_OF_THE_FOLLOWING_ASSUMPTION_IS_TRUE_FOR_RIVET_CONNECTION??$ |
| A. | friction between plates is considered |
| B. | distribution of direct stress on portions of plates between rivet holes is uniform |
| C. | bending stresses are considered |
| D. | shear stress is not uniform on cross section of rivet |
| Answer» C. bending stresses are considered | |
| 5. |
Rivets_in_group_subjected_to_direct_loads_share_load_________$ |
| A. | equally |
| B. | unequally |
| C. | according to rivet diameter |
| D. | rivets are not used in groups |
| Answer» B. unequally | |
| 6. |
Tolerance on length for rivet diameter > 16mm is____? |
| A. | 1.5mm |
| B. | 2mm |
| C. | 5mm |
| D. | 3mm |
| Answer» E. | |
| 7. |
Height of head for flat countersunk head rivet is ______ |
| A. | 0.7d, where d=nominal rivet diameter |
| B. | 0.5d, where d=nominal rivet diameter |
| C. | 0.43d, where d=nominal rivet diameter |
| D. | 0.25d, where d=nominal rivet diameter |
| Answer» D. 0.25d, where d=nominal rivet diameter | |
| 8. |
Diameter of head for button head rivet is ______ |
| A. | 1.60d, where d=nominal rivet diameter |
| B. | 2.5d, where d=nominal rivet diameter |
| C. | 3d, where d=nominal rivet diameter |
| D. | 5d, where d=nominal rivet diameter |
| Answer» B. 2.5d, where d=nominal rivet diameter | |
| 9. |
Which of the following about rivet is correct? |
| A. | causes low level of noise pollution |
| B. | it does not require skilled work |
| C. | labour cost is low |
| D. | removing poorly installed rivet is costly |
| Answer» E. | |
| 10. |
Hammering is done in rivet to _______ |
| A. | give proper shape to rivet |
| B. | completely fill up the rivet hole |
| C. | partially fill up the rivet hole |
| D. | make a rivet hole |
| Answer» C. partially fill up the rivet hole | |
| 11. |
Size of rivet hole is _________ size of rivet |
| A. | more than |
| B. | less than |
| C. | equal to |
| D. | not compared with |
| Answer» B. less than | |
| 12. |
What is riveting? |
| A. | the process of making holes in the structure |
| B. | process of making mould for structure |
| C. | method of joining together pieces of metal by inserting ductile metal pins called rivets |
| D. | method of joining together pieces of metal by inserting non ductile metal pins called rivets |
| Answer» D. method of joining together pieces of metal by inserting non ductile metal pins called rivets | |