MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 24 Mcqs, each offering curated multiple-choice questions to sharpen your Networking knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
What protocols are used to configure trunking on a switch?1. VLAN Trunking Protocol2. VLAN3. 802.1Q4. ISL%! |
| A. | 1 and 2 |
| B. | 3 and 4 |
| C. | 1 only |
| D. | 2 only |
| Answer» C. 1 only | |
| 2. |
If you wanted to delete the configuration stored in NVRAM, what would you type?%! |
| A. | erase startup |
| B. | erase nvram |
| C. | delete nvram |
| D. | erase running |
| Answer» B. erase nvram | |
| 3. |
Which command is used to upgrade an IOS on a Cisco router?%! |
| A. | copy tftp run |
| B. | copy tftp start |
| C. | config net |
| D. | copy tftp flash |
| Answer» E. | |
| 4. |
You have 10 users plugged into a hub running 10Mbps half-duplex. There is a server connected to the switch running 10Mbps half-duplex as well. How much bandwidth does each host have to the server?%! |
| A. | 100 kbps |
| B. | 1 Mbps |
| C. | 2 Mbps |
| D. | 10 Mbps |
| Answer» E. | |
| 5. |
*/*_You have 10 users plugged into a hub running 10Mbps half-duplex. There is a server connected to the switch running 10Mbps half-duplex as well. How much bandwidth does each host have to the server?? |
| A. | 100 kbps |
| B. | 1 Mbps |
| C. | 2 Mbps |
| D. | 10 Mbps |
| Answer» E. | |
| 6. |
*/*_Which protocol is used to send a destination network unknown message back to originating hosts?? |
| A. | TCP |
| B. | ARP |
| C. | ICMP |
| D. | BootP |
| Answer» D. BootP | |
| 7. |
*/*_Which of the following commands will allow you to set your Telnet password on a Cisco router?? |
| A. | line telnet 0 4 |
| B. | line aux 0 4 |
| C. | line vty 0 4 |
| D. | line con 0 |
| Answer» D. line con 0 | |
| 8. |
*/*_Which one of the following is true regarding VLANs?? |
| A. | Two VLANs are configured by default on all Cisco switches. |
| B. | VLANs only work if you have a complete Cisco switched internetwork. No off-brand switches are allowed. |
| C. | You should not have more than 10 switches in the same VTP domain. |
| D. | VTP is used to send VLAN information to switches in a configured VTP domain. |
| Answer» E. | |
| 9. |
*/*_Which class of IP address has the most host addresses available by default?? |
| A. | A |
| B. | B |
| C. | C |
| D. | A and B |
| Answer» B. B | |
| 10. |
*/*_Which protocol does Ping use?? |
| A. | TCP |
| B. | ARP |
| C. | ICMP |
| D. | BootP |
| Answer» D. BootP | |
| 11. |
_ What does the passive command provide to dynamic routing protocols?$? |
| A. | Stops an interface from sending or receiving periodic dynamic updates. |
| B. | Stops an interface from sending periodic dynamic updates but not from receiving updates. |
| C. | Stops the router from receiving any dynamic updates. |
| D. | Stops the router from sending any dynamic updates. |
| Answer» C. Stops the router from receiving any dynamic updates. | |
| 12. |
_ Which router command allows you to view the entire contents of all access lists?$? |
| A. | show all access-lists |
| B. | show access-lists |
| C. | show ip interface |
| D. | show interface |
| Answer» C. show ip interface | |
| 13. |
_ What command is used to create a backup configuration?$? |
| A. | copy running backup |
| B. | copy running-config startup-config |
| C. | config mem |
| D. | wr mem |
| Answer» C. config mem | |
| 14. |
_ What does the passive command provide to dynamic routing protocols?$? |
| A. | Stops an interface from sending or receiving periodic dynamic updates. |
| B. | Stops an interface from sending periodic dynamic updates but not from receiving updates. |
| C. | Stops the router from receiving any dynamic updates. |
| D. | Stops the router from sending any dynamic updates. |
| Answer» C. Stops the router from receiving any dynamic updates. | |
| 15. |
_ What protocol does PPP use to identify the Network layer protocol?$? |
| A. | NCP |
| B. | ISDN |
| C. | HDLC |
| D. | LCP |
| Answer» B. ISDN | |
| 16. |
_ If your router is facilitating a CSU/DSU, which of the following commands do you need to use to provide the router with a 64000bps serial link?$? |
| A. | RouterA (config) #bandwidth 64 |
| B. | RouterA (config-if) #bandwidth 64000 |
| C. | RouterA (config-if) #clock rate 64 |
| D. | RouterA (config-if) #clock rate 64000 |
| Answer» E. | |
| 17. |
_ Which router command allows you to view the entire contents of all access lists?$? |
| A. | show all access-lists |
| B. | show access-lists |
| C. | show ip interface |
| D. | show interface |
| Answer» C. show ip interface | |
| 18. |
_ What command will display the line, protocol, DLCI, and LMI information of an interface?$? |
| A. | sh pvc |
| B. | show interface |
| C. | show frame-relay pvc |
| D. | show run |
| Answer» C. show frame-relay pvc | |
| 19. |
What are the two main types of access control lists (ACLs)?1. Standard2. IEEE3. Extended4. Specialized$? |
| A. | 1 and 3 |
| B. | 2 and 4 |
| C. | 3 and 4 |
| D. | 1 and 2 |
| Answer» B. 2 and 4 | |
| 20. |
Where is a hub specified in the OSI model?$? |
| A. | Session layer |
| B. | Physical layer |
| C. | Data Link layer |
| D. | Application layer |
| Answer» C. Data Link layer | |
| 21. |
To back up an IOS, what command will you use?$? |
| A. | backup IOS disk |
| B. | copy ios tftp |
| C. | copy tftp flash |
| D. | copy flash tftp |
| Answer» E. | |
| 22. |
What is a stub network?$? |
| A. | A network with more than one exit point. |
| B. | A network with more than one exit and entry point. |
| C. | A network with only one entry and no exit point. |
| D. | A network that has only one entry and exit point. |
| Answer» E. | |
| 23. |
What does the command routerA (config) #line cons 0 allow you to perform next?$? |
| A. | Set the Telnet password. |
| B. | Shut down the router. |
| C. | Set your console password. |
| D. | Disable console connections. |
| Answer» D. Disable console connections. | |
| 24. |
How many collision domains are created when you segment a network with a 12-port switch?$? |
| A. | 1 |
| B. | 2 |
| C. | 5 |
| D. | 12 |
| Answer» E. | |