MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 56 Mcqs, each offering curated multiple-choice questions to sharpen your Digital Image Processing knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
During marking, the reference surface is provided by _____. |
| A. | work piece |
| B. | bore gauge |
| C. | marking-off table |
| D. | sketch of the job |
| Answer» D. sketch of the job | |
| 2. |
A file having 20 teeth (approximately) per 1 inch is generally termed as a ______ file. |
| A. | rough |
| B. | second cut |
| C. | dead-smooth |
| D. | smooth |
| Answer» B. second cut | |
| 3. |
From which material is a hammer made? |
| A. | Drop-forged carbon steel |
| B. | Wrought Iron |
| C. | Mild steel |
| D. | Cast iron |
| Answer» B. Wrought Iron | |
| 4. |
File used for removing metal in large quantity _______ |
| A. | Smooth file |
| B. | Second cut file |
| C. | Bastard file |
| D. | Triangular file |
| Answer» D. Triangular file | |
| 5. |
A hollow punch is used for punching holes in ______ . |
| A. | leather |
| B. | cast iron |
| C. | gold |
| D. | mild steel |
| Answer» B. cast iron | |
| 6. |
A master height gauge is used to measure _____. |
| A. | concentricity |
| B. | groove widths |
| C. | pitches |
| D. | hole location |
| Answer» B. groove widths | |
| 7. |
______ is NOT a part of a combination set. |
| A. | Center head |
| B. | Protractor head |
| C. | Slip gauge |
| D. | Square head |
| Answer» D. Square head | |
| 8. |
A tapping hole should be ______ the tap size. |
| A. | equal to |
| B. | 10 mm bigger than |
| C. | larger than |
| D. | smaller than |
| Answer» E. | |
| 9. |
Grade A 'V' blocks are available only up to _______ length. |
| A. | 100 mm |
| B. | 500 mm |
| C. | 700 mm |
| D. | 900 mm |
| Answer» B. 500 mm | |
| 10. |
On which part of the Vernier height gauge, are the main scale division graduated? |
| A. | Fine adjusting nut |
| B. | Base |
| C. | Beam |
| D. | Scriber |
| Answer» D. Scriber | |
| 11. |
For flowering or frosting _____ scraper is used |
| A. | Triangular |
| B. | Hook |
| C. | Flat |
| D. | Bull nose |
| Answer» C. Flat | |
| 12. |
Parallel blocks are used for_______. |
| A. | levelling machine tools |
| B. | setting workplace horizontal |
| C. | cutting parallel keys |
| D. | marking parallel lines along an edge |
| Answer» C. cutting parallel keys | |
| 13. |
_____ is the range of bevel protractor. |
| A. | 0 – 180° |
| B. | 90° – 270° |
| C. | 0 – 90° |
| D. | 0 – 360° |
| Answer» B. 90° – 270° | |
| 14. |
A slight convexity is given to the cutting edges of flat chisel to ______. |
| A. | allow the lubricant to enter |
| B. | cut sharp corners |
| C. | prevent digging of the ends of cutting edge |
| D. | cut curved surfaces |
| Answer» D. cut curved surfaces | |
| 15. |
High carbon steels are machined using tools having |
| A. | Small positive rake angle |
| B. | Large positive rake angle |
| C. | Zero rake angle |
| D. | Negative rake angle |
| Answer» D. Negative rake angle | |
| 16. |
Fine adjusting screw of a Vernier caliper is used to ____. |
| A. | lock Vernier carrier |
| B. | take accurate measurement |
| C. | lock inner jaw |
| D. | lock fine dusting carrier |
| Answer» C. lock inner jaw | |
| 17. |
Indexing fixture is used in _______ |
| A. | Surface finishing on a milling machine. |
| B. | Countersink boring on a drilling machine. |
| C. | Turning operation on a lathe. |
| D. | Gear cutting operation on a milling machine. |
| Answer» E. | |
| 18. |
Least count of steel rule is ________. |
| A. | 0.1 mm |
| B. | 0.05 mm |
| C. | 0.01 mm |
| D. | 0.5 mm |
| Answer» E. | |
| 19. |
A hole is to be made on mild steel with a 12 mm diameter reamer. If the under size is 0.3 mm and if the oversize is 0.05 mm, what will be the diameter of the drill for drilling the hole before reaming? |
| A. | 11.65 mm |
| B. | 12.35 mm |
| C. | 10.70 mm |
| D. | 12.05 mm |
| Answer» B. 12.35 mm | |
| 20. |
For tapping with M5 × 0.8 tap, what size of drill will you use? |
| A. | 4.8 mm |
| B. | 3.0 mm |
| C. | 3.5 mm |
| D. | 4.2 mm |
| Answer» E. | |
| 21. |
In tool signature, nose radius is indicated |
| A. | in the middle |
| B. | in the beginning |
| C. | not indicated |
| D. | at the end |
| Answer» E. | |
| 22. |
A Vernier scale is good enough to read in _____ after the decimal. |
| A. | One digit |
| B. | Two digits |
| C. | Three digits |
| D. | Four digits |
| Answer» C. Three digits | |
| 23. |
For marking round-shaped work piece_____ can be used. |
| A. | Vee block |
| B. | Angle plate |
| C. | Try square |
| D. | None of these |
| Answer» E. | |
| 24. |
A block level can be used for checking _____. |
| A. | only vertical alignment |
| B. | only horizontal alignment |
| C. | only angular alignment |
| D. | vertical & horizontal alignment |
| Answer» E. | |
| 25. |
Constant measuring pressure in micrometer screw gauge is ensured by |
| A. | Lock nut |
| B. | Barrel and Thimble |
| C. | Spanner |
| D. | Ratchet screw |
| Answer» E. | |
| 26. |
How many divisions are graduated on the thimble of micrometer? |
| A. | 15 |
| B. | 50 |
| C. | 25 |
| D. | 40 |
| Answer» C. 25 | |
| 27. |
A prick punch having angle of taper 60° is used for _____. |
| A. | punching marks for holes to be drilled |
| B. | removing broken thread |
| C. | locating hole position |
| D. | locating divider points |
| Answer» B. removing broken thread | |
| 28. |
Dial gauge typically measure in the range of _____. |
| A. | 600 mm to 700 mm |
| B. | 400 to 500 mm |
| C. | 800 to 900 mm |
| D. | 0.25 to 300 mm |
| Answer» E. | |
| 29. |
Plain ring gauges are used to check: |
| A. | accuracy of external threads |
| B. | accuracy of internal of work piece |
| C. | inside diameter of work piece |
| D. | outside diameter of work piece |
| Answer» E. | |
| 30. |
Least count of Vernier depth gauge ____ |
| A. | 0.02 mm |
| B. | 0.1 mm |
| C. | 0.01 mm |
| D. | 0.001 mm |
| Answer» B. 0.1 mm | |
| 31. |
Choose the best device to hold and locate a round bar for drilling. |
| A. | 'V’-block |
| B. | Adjustable locator |
| C. | Pin locator |
| D. | Wedge type location |
| Answer» B. Adjustable locator | |
| 32. |
Name the instrument to measure height of block step. |
| A. | Tube micrometer |
| B. | Outside micrometer |
| C. | Depth micrometer |
| D. | Inside micrometer |
| Answer» D. Inside micrometer | |
| 33. |
A sine bar is used to measure the angle between the height of a slip gauge and the |
| A. | width of the sine bar |
| B. | height of the sine bar |
| C. | number of the slip gauge |
| D. | length of the sine bar |
| Answer» E. | |
| 34. |
A standard hacksaw blade of 300 mm length has 375 teeth. What is the classification and type of set of the blade? |
| A. | Medium, Wave set |
| B. | Medium, Staggered set |
| C. | Fine, Staggered set |
| D. | Fine, Wave set |
| Answer» E. | |
| 35. |
Marking media used for casting & forging surfaces is ________. |
| A. | Chalk powder |
| B. | Prussiam blue |
| C. | Copper sulphate |
| D. | Cellulose Lacquer |
| Answer» B. Prussiam blue | |
| 36. |
A dial gauge is a |
| A. | measuring instrument |
| B. | comparator |
| C. | limit gauge |
| D. | inspection fixture |
| Answer» C. limit gauge | |
| 37. |
At which position of Vernier height gauge, the scriber is on the same level (coplanar) as the base. |
| A. | Vernier scale at 3/4 th position. |
| B. | Vernier scale at middle position |
| C. | Vernier scale at ¼ th position. |
| D. | When Vernier scale reads zero. |
| Answer» E. | |
| 38. |
Bench vice is an example of: |
| A. | Jig |
| B. | Fixture |
| C. | Locator |
| D. | Clamping device |
| Answer» E. | |
| 39. |
High speed steel is an alloy of |
| A. | 18% tungsten, 12% chromium and 4% Vanadium |
| B. | 30% chromium, 20% tungsten and 4% carbon |
| C. | 18% tungsten, 6% chromium and 4% Vanadium |
| D. | 18% tungsten, 4% chromium and 2% Vanadium |
| Answer» E. | |
| 40. |
A mallet is generally made up of _____ |
| A. | cast iron |
| B. | chrome vanadium |
| C. | mild steel |
| D. | wood |
| Answer» E. | |
| 41. |
An outside micrometer has a negative error. The correct reading can be taken by: |
| A. | adding twice the negative error in the actual reading |
| B. | adding the negative error in the actual reading |
| C. | deducing the negative error from the actual reading |
| D. | deducting twice the negative error from the actual reading |
| Answer» C. deducing the negative error from the actual reading | |
| 42. |
Match the pairs of instruments and their applications:List-I InstrumentsList-II ApplicationsI.Tool Makers MicroscopeA.Surface profileII.AutocollimatorB.Thread profile parametersIII.Dial gauge with standC.Squareness testingIV.TalysurfD.Machine settingSelect the correct pairs from the following: |
| A. | I-B, II-C, III-D, IV-A |
| B. | I-A, II-B, III-C, IV-D |
| C. | I-B, II-A, III-C, IV-D |
| D. | I-B, II-D, III-A, IV-C |
| Answer» B. I-A, II-B, III-C, IV-D | |
| 43. |
It works on the principle of rake & pinion. |
| A. | Vernier bevel protactor |
| B. | Dial test indicator |
| C. | Vernier height gauge |
| D. | Micrometer |
| Answer» C. Vernier height gauge | |
| 44. |
Identify the file having flat, triangular face with teeth on the wide face only used for finishing sharp corners. |
| A. | Riffler file |
| B. | Crossing file |
| C. | Barrette file |
| D. | Mill saw file |
| Answer» D. Mill saw file | |
| 45. |
A snap gauge is: |
| A. | cylindrical |
| B. | oval shaped |
| C. | ‘C’ shaped |
| D. | square shaped |
| Answer» D. square shaped | |
| 46. |
How many teeth of taper tap bottom are chamfered? |
| A. | 1 to 2 |
| B. | 4 to 6 |
| C. | 20 to 30 |
| D. | 7 to 10 |
| Answer» B. 4 to 6 | |
| 47. |
IMAGE_PROCESSING_APPROACHES_OPERATING_DIRECTLY_ON_PIXELS_OF_INPUT_IMAGE_WORK_DIRECTLY_IN_____________?$ |
| A. | Transform domain |
| B. | Spatial domain |
| C. | Inverse transformation |
| D. | None of the Mentioned |
| Answer» C. Inverse transformation | |
| 48. |
Imaging systems having physical artefacts embedded in the imaging sensors produce a set of points called _________? |
| A. | Tie Points |
| B. | Control Points |
| C. | Reseau Marks |
| D. | None of the Mentioned |
| Answer» D. None of the Mentioned | |
| 49. |
Consider two regions A and B composed of foreground pixels. The ________ of these two sets is the set of elements belonging to set A or set B or both. |
| A. | OR |
| B. | AND |
| C. | NOT |
| D. | XOR |
| Answer» B. AND | |
| 50. |
If every element of a set A is also an element of a set B, then A is said to be a _________ of set B. |
| A. | Disjoint set |
| B. | Union |
| C. | Subset |
| D. | Complement set |
| Answer» D. Complement set | |