MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 657 Mcqs, each offering curated multiple-choice questions to sharpen your Testing Subject knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
The camshaft controls |
| A. | Valve closing |
| B. | Valve opening |
| C. | Valve timing |
| D. | All are correct |
| Answer» E. | |
| 2. |
The gang angle of disc harrow is adjusted in the range of |
| A. | 0-30? |
| B. | 30-60? |
| C. | 60-90? |
| D. | Above 90? |
| Answer» B. 30-60? | |
| 3. |
The increase in tilt angle of disc plough influences |
| A. | Penetration of disc |
| B. | Width of cut |
| C. | Reduce penetration of disc |
| D. | Reduce width of cut |
| Answer» B. Width of cut | |
| 4. |
The mould board plough absorb side forces mainly through the |
| A. | Share |
| B. | Mould board |
| C. | Land disc |
| D. | Frog |
| Answer» D. Frog | |
| 5. |
Heavy smoking in an engine during operation may be due to |
| A. | Rich mixture |
| B. | Overloading |
| C. | Late injection |
| D. | All are correct |
| Answer» E. | |
| 6. |
A thresher causes more seed damage if |
| A. | Speed is increased |
| B. | Clearance increased |
| C. | Speed is decreased |
| D. | Feed rate is reduced |
| Answer» B. Clearance increased | |
| 7. |
Medium size bullock can develop |
| A. | 0.50 to 0.75 hp |
| B. | 0.75 to 1.0 hp |
| C. | 0.75 hp to 1.1 hp |
| D. | 1.0 to 1.5 hp |
| Answer» B. 0.75 to 1.0 hp | |
| 8. |
The mechanical efficiency of spray pumps ranges from |
| A. | 50-60% |
| B. | 50-70% |
| C. | 50-80% |
| D. | 50-90 % |
| Answer» E. | |
| 9. |
The fan of radiator is driven by |
| A. | Camshaft |
| B. | Crankshaft |
| C. | Flywheel |
| D. | All are correct |
| Answer» B. Crankshaft | |
| 10. |
Parboiling of paddy is done to |
| A. | Achieve maximum recovery of head rice |
| B. | Minimise the broken percentage |
| C. | Reduce the milling losses |
| D. | All are correct |
| Answer» E. | |
| 11. |
Which of the biogas plant has digester tank and gasholder as combined unit? |
| A. | Floating dome type |
| B. | Fixed dome type |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» C. Both (a) & (b) | |
| 12. |
Sun radiation temperature corresponding to black body temperature is at about |
| A. | 3000 K more |
| B. | 5000 K more |
| C. | 6000 K more |
| D. | 7000 K more |
| Answer» D. 7000 K more | |
| 13. |
Secondary fuel filter is used to remove the particles of size |
| A. | 1 Micron |
| B. | 2 Micron |
| C. | 3 Micron |
| D. | 4 Micron |
| Answer» C. 3 Micron | |
| 14. |
Contour trenching is performed to |
| A. | Control the landslide from the hill face |
| B. | Conserve the moisture |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» C. Both (a) & (b) | |
| 15. |
The uneven furrow formation in disc ploughing is due to |
| A. | Disc angle is not uniform |
| B. | Loose bearing of disc |
| C. | Hitching defects of disc plough |
| D. | All are correct |
| Answer» E. | |
| 16. |
Erosivity is the |
| A. | Climatic aggressiveness |
| B. | Soil aggressiveness |
| C. | Both (a) and (b) |
| D. | None of these |
| Answer» B. Soil aggressiveness | |
| 17. |
The shape of furrow cut by MB plough is |
| A. | V-shape |
| B. | L-shape |
| C. | W-shape |
| D. | M-shape |
| Answer» C. W-shape | |
| 18. |
A splined shaft used for taking off power from engine is |
| A. | Final drive |
| B. | Drawbar |
| C. | Power takes off |
| D. | Differential |
| Answer» D. Differential | |
| 19. |
Centrifugal governor is also termed as |
| A. | Maximum speed governor |
| B. | Minimum speed governor |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» B. Minimum speed governor | |
| 20. |
In disc harrow the angle made by the axis of the arbor bolt with the direction of travel is |
| A. | Disc angle |
| B. | Tilt angle |
| C. | Gang angle |
| D. | None of these |
| Answer» D. None of these | |
| 21. |
Clutch and differential are part of |
| A. | Injection system |
| B. | Power transmission system |
| C. | PTO drive |
| D. | None of these |
| Answer» C. PTO drive | |
| 22. |
Calorific value of natural gas ranges between |
| A. | 10-15 Kj/kg |
| B. | 20-30 Kj/kg |
| C. | 33.50 KJ/kg |
| D. | 50-75 KJ/kg |
| Answer» D. 50-75 KJ/kg | |
| 23. |
Ballasting in front tyre of tractor is done for |
| A. | Increasing traction |
| B. | Decreasing load |
| C. | Increasing stability |
| D. | All are correct |
| Answer» D. All are correct | |
| 24. |
Grassed waterways are used as |
| A. | Diversion channels |
| B. | Outlets |
| C. | Inlet to terrace system |
| D. | All are correct |
| Answer» C. Inlet to terrace system | |
| 25. |
The un-damped natural frequency of seat suspension system with mzximum travel of 76 mm should be |
| A. | 1.0 Hz |
| B. | 1.5 Hz |
| C. | 2.0 Hz |
| D. | 1.5 Hz |
| Answer» C. 2.0 Hz | |
| 26. |
The annual runoff from the catchments in cm is |
| A. | 42 |
| B. | 45.4 |
| C. | 47.3 |
| D. | 110 |
| Answer» C. 47.3 | |
| 27. |
Nozzle spacing in boom is governed by |
| A. | Inclined |
| B. | Axial horizontal |
| C. | Axial vertical |
| D. | All are correct |
| Answer» D. All are correct | |
| 28. |
The common type of battery used in IC engines is |
| A. | Dry battery |
| B. | Lead acid battery |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» C. Both (a) & (b) | |
| 29. |
Factor which affects the flood hydrograph, is |
| A. | Shape of basin |
| B. | Size of basin |
| C. | Slope of basin |
| D. | All are correct |
| Answer» E. | |
| 30. |
The upper strata of the earth where the openings are completely filled with water are |
| A. | Zone of fracture |
| B. | Zone of aeration |
| C. | Zone of saturation |
| D. | None of these |
| Answer» D. None of these | |
| 31. |
The water level stands in the well before pumping is |
| A. | Static water level |
| B. | Pumping water level |
| C. | Piezometric level |
| D. | Draw down |
| Answer» B. Pumping water level | |
| 32. |
The maximum operating depth for disc harrow is about |
| A. | One-half of the disc diameter |
| B. | One -third of the disc diameter |
| C. | One-fifth of the disc diameter |
| D. | One-fourth of disc diameter |
| Answer» E. | |
| 33. |
In a gyratory crusher, the speed of crushing head ranges from |
| A. | 100-200 gyration/min |
| B. | 125/425 gyration/min |
| C. | 150-500 gyration/min |
| D. | 175-650 gyration/min |
| Answer» C. 150-500 gyration/min | |
| 34. |
In thermo siphon system, fan is operated by |
| A. | Crankshaft |
| B. | Camshaft |
| C. | Flywheel |
| D. | All are correct |
| Answer» B. Camshaft | |
| 35. |
Rocker sprayer is used for spraying |
| A. | Small crops |
| B. | Tall crops |
| C. | Godown and factories |
| D. | All are correct |
| Answer» E. | |
| 36. |
Spark occurs when |
| A. | Points open |
| B. | Points close |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» B. Points close | |
| 37. |
Seed drill are used for sowing |
| A. | Small seeds |
| B. | Bolder seeds |
| C. | Seedlings |
| D. | Plants |
| Answer» B. Bolder seeds | |
| 38. |
The disc used in Olpad thresher for threshing purpose is |
| A. | Plane |
| B. | Notched |
| C. | Serrated |
| D. | All are correct |
| Answer» C. Serrated | |
| 39. |
In sun drying, the relative humidity (per day) of grain under favourable conditions is reduced by |
| A. | 1-2% |
| B. | 3-4% |
| C. | 5-6% |
| D. | 7-8% |
| Answer» C. 5-6% | |
| 40. |
Toe-in provide in tractor is approximately |
| A. | 7 - 10 mm |
| B. | 10 - 15 mm |
| C. | 12 - 16 mm |
| D. | 15 - 20 mm |
| Answer» B. 10 - 15 mm | |
| 41. |
The carburetor employed on most of tractor engines is |
| A. | Down draft |
| B. | Middle draft |
| C. | Updraft |
| D. | None of these |
| Answer» D. None of these | |
| 42. |
Of the following, which is the essential part of steering mechanism? |
| A. | Tie rod |
| B. | Steering wheel |
| C. | Drag link |
| D. | All are correct |
| Answer» E. | |
| 43. |
Crankcase breather is used for |
| A. | Cleaning the dust particles |
| B. | See the level of oil |
| C. | Removing water vapour from crankcase |
| D. | All are correct |
| Answer» D. All are correct | |
| 44. |
A sheet of water, which overflows a weir, is |
| A. | Head |
| B. | Nape |
| C. | Both (a) and (b) |
| D. | None of these |
| Answer» C. Both (a) and (b) | |
| 45. |
The carburetor is main part of |
| A. | Diesel engine |
| B. | Steam engine |
| C. | Petrol engine |
| D. | Gas engine |
| Answer» D. Gas engine | |
| 46. |
In individual pump system, fuel is delivered to injector at a high pressure of |
| A. | 500-1000 Kpa |
| B. | 1000-5000 Kpa |
| C. | 5000-10000 Kpa |
| D. | 10000-20000 Kpa |
| Answer» E. | |
| 47. |
In an engine, the angle between the cylinder axes and the crankshaft centre line is |
| A. | 60? |
| B. | 90? |
| C. | 180? |
| D. | 120? |
| Answer» C. 180? | |
| 48. |
In multi-blade rotor the number of blades varies from |
| A. | 8?11 |
| B. | 10?16 |
| C. | 12?20 |
| D. | 14?26 |
| Answer» D. 14?26 | |
| 49. |
Wind velocity varies with |
| A. | Temperature |
| B. | Density of air |
| C. | Viscosity of air |
| D. | All are correct |
| Answer» B. Density of air | |
| 50. |
The position of seepage line is influenced by |
| A. | Permeability of fill materials |
| B. | Permeability of foundation materials |
| C. | Both (a) and (b) |
| D. | None of these |
| Answer» D. None of these | |