MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 19 Mcqs, each offering curated multiple-choice questions to sharpen your Manufacturing Engineering knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Which of the following is made of wood? |
| A. | Gate |
| B. | Riser |
| C. | Bottom board |
| D. | Chill |
| Answer» D. Chill | |
| 2. |
Which of the following term can be used to describe flask? |
| A. | Drag |
| B. | Cope |
| C. | Check |
| D. | Chill |
| Answer» E. | |
| 3. |
The replica of the final object to be made is known as? |
| A. | Parting line |
| B. | Flask |
| C. | Pattern |
| D. | Mould |
| Answer» D. Mould | |
| 4. |
The channel through which metal or plastic is poured into a mould? |
| A. | Sprue |
| B. | Gate |
| C. | Flask |
| D. | Riser |
| Answer» B. Gate | |
| 5. |
The passageways in the parting plane through which molten flow is regulated is known as? |
| A. | Core |
| B. | Chaplet |
| C. | Gate |
| D. | Runner |
| Answer» E. | |
| 6. |
The riser is a reservoir of molten metal provided in the casting so that hot metal can flow back into the mould cavity when there is a reduction in the volume of metal due to? |
| A. | Compression |
| B. | Solidification |
| C. | Expansion |
| D. | Melting |
| Answer» C. Expansion | |
| 7. |
A small funnel shaped cavity at the top of the mould into which the metal is poured is known as? |
| A. | Sprue |
| B. | Core |
| C. | Pouring basin |
| D. | Gate |
| Answer» D. Gate | |
| 8. |
Which of the following is an entry point through which molten metal enters mould cavity? |
| A. | Gate |
| B. | Chaplet |
| C. | Chill |
| D. | Riser |
| Answer» B. Chaplet | |
| 9. |
The lower molding flask is also known as? |
| A. | Drag |
| B. | Cope |
| C. | Check |
| D. | Chill |
| Answer» B. Cope | |
| 10. |
WHICH_OF_THE_FOLLOWING_IS_MADE_OF_WOOD??$ |
| A. | Gate |
| B. | Riser |
| C. | Bottom board |
| D. | Chill |
| Answer» D. Chill | |
| 11. |
Depending upon the position of the flask in the mould structure the flask is also referred a? |
| A. | Drag |
| B. | Cope |
| C. | Check |
| D. | All of the Mentioned |
| Answer» E. | |
| 12. |
The replica of the final object to be made is known a? |
| A. | Parting line |
| B. | Flask |
| C. | Pattern |
| D. | Mould |
| Answer» D. Mould | |
| 13. |
The passageway through which the molten metal from the pouring basin reaches the mould cavity is known as |
| A. | Sprue |
| B. | Gate |
| C. | Flask |
| D. | Riser |
| Answer» B. Gate | |
| 14. |
The passage ways in the parting plane through which molten flow is regulated is known as |
| A. | Core |
| B. | Chaplet |
| C. | Gate |
| D. | Runner |
| Answer» E. | |
| 15. |
Riser is a reservoir of molten metal provided in the casting so that hot metal can flow back into the mould cavity when there is a reduction in the volume of metal due to |
| A. | Compression |
| B. | Solidification |
| C. | Expansion |
| D. | None of the Mentioned |
| Answer» C. Expansion | |
| 16. |
Which of the following is used to support the cavity from inside? |
| A. | Chill |
| B. | Chaplet |
| C. | Sprue |
| D. | Core |
| Answer» C. Sprue | |
| 17. |
A small funnel shaped cavity at the top of the mould into which the metal is poured is known as |
| A. | Sprue |
| B. | Core |
| C. | Pouring basin |
| D. | Gate |
| Answer» D. Gate | |
| 18. |
The entry point through which molten metal enters mould cavity is by |
| A. | Gate |
| B. | Chaplet |
| C. | Chill |
| D. | Riser |
| Answer» B. Chaplet | |
| 19. |
The lower molding flask is also known as |
| A. | Drag |
| B. | Cope |
| C. | Check |
| D. | None of the Mentioned |
| Answer» B. Cope | |