Which statement is true regarding classless routing protocols?1. The use of discontiguous networks is not allowed.2. The use of variable length subnet masks is permitted.3. RIPv1 is a classless routing protocol.4. IGRP supports classless routing within the same autonomous system.5. RIPv2 supports classless routing.

Which statement is true regarding classless routing protocols?1. The u

1.	Which statement is true regarding classless routing protocols?1. The use of discontiguous networks is not allowed.2. The use of variable length subnet masks is permitted.3. RIPv1 is a classless routing protocol.4. IGRP supports classless routing within the same autonomous system.5. RIPv2 supports classless routing.
A.	, 3 and 5
B.	and 4
C.	and 5
D.	one of the above
Answer» D. one of the above

Discussion

No Comment Found

Related MCQs

You type on your router console and see that 172.16.10.0 is being advertised to you with a metric of 16. What does this mean?
Which of the following statements are true regarding the command ?
A network administrator views the output from the command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?
You have the following routing table. Which of the following networks will not be placed in the neighbor routing table?R192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0C192.168.40.0/24 is directly connected, Serial0172.16.0.0/24 is subnetted, 1 subnetsC172.16.30.0 is directly connected, Loopback0R192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0R10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0C192.168.50.0/24 is directly connected, Ethernet0
Which statement is true regarding classless routing protocols?1. The use of discontiguous networks is not allowed.2. The use of variable length subnet masks is permitted.3. RIPv1 is a classless routing protocol.4. IGRP supports classless routing within the same autonomous system.5. RIPv2 supports classless routing.
The Corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. Looking at the output from the Corporate router, what will the router do with this packet?Corp#sh ip route[output cut]R192.168.215.0 [120/2] via 192.168.20.2, 00:00:23, Serial0/0R192.168.115.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0R192.168.30.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0C192.168.20.0 is directly connected, Serial0/0C192.168.214.0 is directly connected, FastEthernet0/0
Which two of the following are true regarding the distance-vector and link-state routing protocols?1. Link state sends its complete routing table out all active interfaces on periodic time intervals.2. Distance vector sends its complete routing table out all active interfaces on periodic time intervals.3. Link state sends updates containing the state of its own links to all routers in the internetwork.4. Distance vector sends updates containing the state of its own links to all routers in the internetwork.
What does RIPv2 use to prevent routing loops?1. CIDR2. Split horizon3. Authentication4. Classless masking5. Holddown timers
Network 206.143.5.0 was assigned to the Acme Company to connect to its ISP. The administrator of Acme would like to configure one router with the commands to access the Internet. Which commands could be configured on the Gateway router to allow Internet access to the entire network?1. Gateway (config) # ip route 0.0.0.0 0.0.0.0206.143.5.22. Gateway (config) # router rip3. Gateway (config-router) # network 206.143.5.04. Gateway (config-router) # network 206.143.5.0 default
IGRP uses which of the following as default parameters for finding the best path to a remote network?1. Hop count2. MTU3. Cumulative interface delay4. STP5. Path bandwidth value

Discussion

No Comment Found

Related MCQs

Reply to Comment