Match the following instruction mnemonics with their description.a. CJNE A,direct,rel ------------ 1. Compare immediate to indirect and Jump if not equalb. CJNE A,#data,rel ------------ 2. Compare direct byte to accumulator and Jump if not equalc. CJNE @R, #data,rel ------- 3. Compare immediate to register and Jump if not equald. CJNE R, # data rel -------- 4. Compare immediate to accumulator and Jump if not equal

Match the following instruction mnemonics with their description.a. CJ

1.	Match the following instruction mnemonics with their description.a. CJNE A,direct,rel ------------ 1. Compare immediate to indirect and Jump if not equalb. CJNE A,#data,rel ------------ 2. Compare direct byte to accumulator and Jump if not equalc. CJNE @R, #data,rel ------- 3. Compare immediate to register and Jump if not equald. CJNE R, # data rel -------- 4. Compare immediate to accumulator and Jump if not equal
A.	A-1, B-2, C-3, D-4
B.	A-2, B-4, C-1, D-3
C.	A-4, B-3, C-2, D-1
D.	A-2, B-4, C-3, D-1
Answer» C. A-4, B-3, C-2, D-1

Discussion

No Comment Found

Related MCQs

How is the baud rate determined on the basis of system clock frequency (f) in accordance to mode '0' of serial communication?
What does the instruction XCHD A, @R signify during the data transfer in the program execution?
How many bytes are supposed to get occupied while subtracting indirect RAM from an accumulator along with borrow under the execution of SUBBA, @R?
What does the following pictorial representation of PUSH operation in the stack pointer indicate among the below stated conclusions/inferences?a. Stack Pointer is incremented by 2b. Location 55H in on-chip stack memory gets loaded with 44Hc. Stack Pointer gets initialized by 56Hd. Data Pointer gets loaded with an immediate data 44H which ultimately leads to initialization of stack pointer
Match the following a. JC rel -------------------- 1. Jump if direct bit is set & clear bitb. JNC rel ------------------ 2. Jump if direct bit is setc. JB bit, rel --------------- 3. Jump if direct bit is not setd. JBC bit, rel ------------ 4. Jump if carry is sete. JNB bit, rel ------------- 5. Jump if carry is not set
Consider the below mentioned statements. Which among them is /are approved to be incorrect in case of calling instructions of program branching?a. Absolute Calls instructions specify 11-bit address and calling subroutine within 2K program memory blockb. Long call instructions specify 16-bit address and subroutine anywhere within 64K program memory blockc. Short call instructions specify 16-bit address and subroutine within 4K program memory blockd. All long call and short call instructions specify 11 bit address and the calling subroutine within 16K program memory block
Match the following instruction mnemonics with their description.a. CJNE A,direct,rel ------------ 1. Compare immediate to indirect and Jump if not equalb. CJNE A,#data,rel ------------ 2. Compare direct byte to accumulator and Jump if not equalc. CJNE @R, #data,rel ------- 3. Compare immediate to register and Jump if not equald. CJNE R, # data rel -------- 4. Compare immediate to accumulator and Jump if not equal
Which minimum mode signal is used for demultiplexing the data and address lines with the assistance of an external latch in a microprocessor while accessing memory segment?
Match the following registers with their functions :a. Line Status Register -------------------- 1. Set Up the communication parametersb. Line Control Register ------------------ 2. Sharing of similar addressesc. Transmit & Receive Buffers --------- 3. Status Determination of Tx & Rr
Which abstraction level undergo the compilation process by converting a sequential program into finite-state machine and register transfers while designing an embedded system?

Discussion

No Comment Found

Related MCQs

Reply to Comment