In Maxwell’s capacitance bridge for calculating unknown inductance, the various values at balance are, R1 = 300 Ω, R2 = 700 Ω, R3 = 1500 Ω, C4 = 0.8 μF. The values of R1, L1 and Q factor, if the frequency is 1100 Hz are ____________

In Maxwell’s capacitance bridge for calculating unknown inductance,

1.	In Maxwell’s capacitance bridge for calculating unknown inductance, the various values at balance are, R1 = 300 Ω, R2 = 700 Ω, R3 = 1500 Ω, C4 = 0.8 μF. The values of R1, L1 and Q factor, if the frequency is 1100 Hz are ____________
A.	240 Ω, 0.12 H, 3.14
B.	140 Ω, 0.168 H, 8.29
C.	140 Ω, 0.12 H, 5.92
D.	240 Ω, 0.36 H, 8.29
Answer» C. 140 Ω, 0.12 H, 5.92

Discussion

No Comment Found

Related MCQs

The four arms of an AC bridge network are as follows:Arm AB: unknown impedanceArm BC: standard capacitor C2 of 1000pfArm CD: a non-inductive resistance of R of 100 Ω in parallel to a capacitor of 0.01 μFArm DA: a non-inductive resistance of 1000 ΩThe supply frequency is 50 Hz and connected across terminals B and D. If the bridge is balanced with the above value, determine the value of unknown Impedance.
In the figure below, the values of the resistance R1 and inductance L1 of a coil are to be calculated after the bridge is balanced. The values are _________________
In Maxwell’s capacitance bridge for calculating unknown inductance, the various values at balance are, R1 = 300 Ω, R2 = 700 Ω, R3 = 1500 Ω, C4 = 0.8 μF. The values of R1, L1 and Q factor, if the frequency is 1100 Hz are ____________
In the Owen’s bridge shown in below figure, Z1 = 200∠60°, Z2 = 400∠-90°, Z3 = 300∠0°, Z4 = 400∠30°. Then,
In the figure given below, a 220 V 50 Hz supplies a 3-phase balanced source. The pressure Coil (PC) and Current Coil (CC) of a watt-meter are connected to the load as shown. The watt-meter reading is _________
The meter constant of a single-phase, 230 V induction watt-meter is 600 rev/kW-h. The speed of the meter disc for a current of 15 A at 0.8 power factor lagging will be?
In the Two wattmeter method of measuring power in a balanced three-phase circuit, one wattmeter shows zero and the other positive maximum. The load power factor is ___________
A 200/1 Current Transformer (CT) is wound with 400 turns on the secondary on a toroidal core. When it carries a current of 180 A on the primary, the ratio is found to be -0.5%. If the number of secondary turns is reduced by 1, the new ratio error (in %) will be?
A resistor of 10 kΩ with a tolerance of 5% is connected in parallel with 5 kΩ resistors of 10% tolerance. The tolerance limit is __________
The simultaneous applications of signals x (t) and y (t) to the horizontal and vertical plates respectively, of an oscilloscope, produce a vertical figure of 8 displays. If P and Q are constants and x(t) = P sin (4t + 30), then y(t) is equal to _________

In Maxwell’s capacitance bridge for calculating unknown inductance, the various values at balance are, R1 = 300 Ω, R2 = 700 Ω, R3 = 1500 Ω, C4 = 0.8 μF. The values of R1, L1 and Q factor, if the frequency is 1100 Hz are ____________

Discussion

No Comment Found

Related MCQs

Reply to Comment