730 + Mcqs in Technical Drawing McqOptions

1.	Quality standards in some industries allow for electronic documents to serve as a permanent record if they are properly controlled.
A.	True
B.	False
Answer» B. False

Discussion

2.	Design databases can be used to streamline the design process.
A.	True
B.	False
Answer» B. False

Discussion

3.	Copper pipe is brittle, and settling can cause fracture unless the joints are sufficiently flexible.
A.	True
B.	False
Answer» C.

Discussion

4.	Joints between pipes, fittings, and valves may be screwed or flanged but not welded or soldered.
A.	True
B.	False
Answer» C.

Discussion

5.	A piece mark should be shown wherever a separately handled member appears on the drawings.
A.	True
B.	False
Answer» B. False

Discussion

6.	Reinforced concrete has embedded steel reinforcing bars.
A.	True
B.	False
Answer» B. False

Discussion

7.	Due to wood loss in surfacing, the nominal size of structural timber is larger than its dressed thickness.
A.	True
B.	False
Answer» B. False

Discussion

8.	Traditionally, brick and tile are built into masonry forms, and units are placed one at a time in a soft mortar.
A.	True
B.	False
Answer» B. False

Discussion

9.	Symbols are seldom used to indicate requirements for finished surfaces on wood.
A.	True
B.	False
Answer» C.

Discussion

10.	The surface of a wood product is finished by milling or planing.
A.	True
B.	False
Answer» B. False

Discussion

11.	Tolerance stacking has little effect on the fit of steel members.
A.	True
B.	False
Answer» C.

Discussion

12.	Brick and tile are some of the less common forms of building construction.
A.	True
B.	False
Answer» C.

Discussion

13.	Riveting is seldom used as a connection method in structural steel.
A.	True
B.	False
Answer» B. False

Discussion

14.	Most CAD programs have structural shapes symbol libraries available.
A.	True
B.	False
Answer» B. False

Discussion

15.	Individual companies often have their own standards of data management.
A.	True
B.	False
Answer» B. False

Discussion

16.	Design milestones and reviews help ensure that the design process is timely.
A.	True
B.	False
Answer» B. False

Discussion

17.	Legal standards for how long engineering drawings need to be retained are standardized in the United States.
A.	True
B.	False
Answer» C.

Discussion

18.	It is important to establish a procedure and name files systematically.
A.	True
B.	False
Answer» B. False

Discussion

19.	If a complicated pictorial is needed, it may be easier and more accurate to create a 3D model than an oblique drawing.
A.	True
B.	False
Answer» B. False

Discussion

20.	If you are sketching an ellipse in an oblique drawing, you can block in the enclosing rectangle and sketch the ellipse tangent to its sides.
A.	True
B.	False
Answer» B. False

Discussion

21.	In oblique projections, one of the object's principal faces is parallel to the plane of projection.
A.	True
B.	False
Answer» B. False

Discussion

22.	When the receding lines are drawn to half size, the drawing is known as a cabinet projection.
A.	True
B.	False
Answer» B. False

Discussion

23.	After a drawing has been released, an engineering change order is used to document and approve drawing changes.
A.	True
B.	False
Answer» B. False

Discussion

24.	When the follower movement is in a plane parallel to the cam shaft, an irregular cam must be employed.
A.	True
B.	False
Answer» C.

Discussion

25.	Plastic pipe is lightweight and corrosionproof, but typically is not resistant to chemicals.
A.	True
B.	False
Answer» C.

Discussion

26.	Single-line drawings show the centerline of the pipe.
A.	True
B.	False
Answer» B. False

Discussion

27.	Axonometric drawings are seldom used in piping drawings.
A.	True
B.	False
Answer» C.

Discussion

28.	Electronic files for the most part have replaced the use of microfilm and microfiche.
A.	True
B.	False
Answer» B. False

Discussion

29.	In a developed piping drawing, horizontal pipes may be revolved into the vertical plane so the entire installation can be shown on one plane.
A.	True
B.	False
Answer» B. False

Discussion

30.	Brass and copper pipe is used in plumbing for supply, soil, waste, drain, and vent lines.
A.	True
B.	False
Answer» B. False

Discussion

31.	A worm is a screw with a thread shaped like a rack tooth.
A.	True
B.	False
Answer» B. False

Discussion

32.	Proportions and shapes of gear teeth are not standardized.
A.	True
B.	False
Answer» C.

Discussion

33.	Gears are used to transmit power and rotating or reciprocating motion from one machine part to another.
A.	True
B.	False
Answer» B. False

Discussion

34.	Bevel gear teeth have the same involute shape as teeth on spur gears but are tapered toward the cone apex.
A.	True
B.	False
Answer» B. False

Discussion

35.	Worm wheels are similar to helical gears cut to conform to the shape of the worm.
A.	True
B.	False
Answer» B. False

Discussion

36.	Working drawings for bevel gears give both the dimensions of the gear blank and the data necessary for cutting the teeth.
A.	True
B.	False
Answer» C.

Discussion

37.	The motion of the follower as it rises or falls depends on the shape of the curves in the displacement diagram.
A.	True
B.	False
Answer» B. False

Discussion

38.	Teeth are spaced by laying out equal angles.
A.	True
B.	False
Answer» B. False

Discussion

39.	Structural steel is available in two standard shapes.
A.	True
B.	False
Answer» C.

Discussion

40.	Structural steel shop drawings are usually calculated to the nearest inch.
A.	True
B.	False
Answer» C.

Discussion

41.	One quick way to view the entire drawing area is to use the Zoom command by typing ________.
A.	type Z enter A enter
B.	type Z enter E enter
C.	type SHOWALL enter
D.	type ALL enter
Answer» B. type Z enter E enter

Discussion

42.	When setting up a mechanical drawing in AutoCAD the drafter should set the units to ________.
A.	fractional
B.	decimal
C.	architectural
D.	metric
Answer» C. architectural

Discussion

43.	When drawing a line using the relative coordinate system a line is created from ________.
A.	0,0
B.	the ending point of the last line
C.	the beginning point of the last line
D.	none of the above
Answer» C. the beginning point of the last line

Discussion

44.	If you use the absolute coordinate system to create a line from a starting point of 0, 0 8 units on the X axis and 5 units on the Y axis you enter ________ for the second point.
A.	8,5
B.	5,8
C.	0,8
D.	5,0
Answer» B. 5,8

Discussion

45.	Circles, circular arcs, and other curved surfaces may be drawn using offset measurements.
A.	True
B.	False
Answer» B. False

Discussion

46.	In general, all types of sections for isometric drawing may be applied to oblique drawing.
A.	True
B.	False
Answer» B. False

Discussion

47.	In an oblique drawing, when an angle is specified in degrees in a receding plane, you should convert the angle into circular measurements.
A.	True
B.	False
Answer» C.

Discussion

48.	In CAD, oblique drawings are difficult to create because you cannot use snap increments or draw similarly to drawing on grid paper.
A.	True
B.	False
Answer» C.

Discussion

49.	Many different types of wood are used as structural timber.
A.	True
B.	False
Answer» B. False

Discussion

50.	In order to set drawing limits for a "C" size architectural drawing the drafter should set the limits to ________.
A.	0,0 and 2,9
B.	0,0 and 17,11
C.	0,0 and 18,24
D.	0,0 and 34,24
Answer» D. 0,0 and 34,24

Discussion

Explore topic-wise MCQs in Testing Subject.

Quality standards in some industries allow for electronic documents to serve as a permanent record if they are properly controlled.

Design databases can be used to streamline the design process.

Copper pipe is brittle, and settling can cause fracture unless the joints are sufficiently flexible.

Joints between pipes, fittings, and valves may be screwed or flanged but not welded or soldered.

A piece mark should be shown wherever a separately handled member appears on the drawings.

Reinforced concrete has embedded steel reinforcing bars.

Due to wood loss in surfacing, the nominal size of structural timber is larger than its dressed thickness.

Traditionally, brick and tile are built into masonry forms, and units are placed one at a time in a soft mortar.

Symbols are seldom used to indicate requirements for finished surfaces on wood.

The surface of a wood product is finished by milling or planing.

Tolerance stacking has little effect on the fit of steel members.

Brick and tile are some of the less common forms of building construction.

Riveting is seldom used as a connection method in structural steel.

Most CAD programs have structural shapes symbol libraries available.

Individual companies often have their own standards of data management.

Design milestones and reviews help ensure that the design process is timely.

Legal standards for how long engineering drawings need to be retained are standardized in the United States.

It is important to establish a procedure and name files systematically.

If a complicated pictorial is needed, it may be easier and more accurate to create a 3D model than an oblique drawing.

If you are sketching an ellipse in an oblique drawing, you can block in the enclosing rectangle and sketch the ellipse tangent to its sides.

In oblique projections, one of the object's principal faces is parallel to the plane of projection.

When the receding lines are drawn to half size, the drawing is known as a cabinet projection.

After a drawing has been released, an engineering change order is used to document and approve drawing changes.

When the follower movement is in a plane parallel to the cam shaft, an irregular cam must be employed.

Plastic pipe is lightweight and corrosionproof, but typically is not resistant to chemicals.

Single-line drawings show the centerline of the pipe.

Axonometric drawings are seldom used in piping drawings.

Electronic files for the most part have replaced the use of microfilm and microfiche.

In a developed piping drawing, horizontal pipes may be revolved into the vertical plane so the entire installation can be shown on one plane.

Brass and copper pipe is used in plumbing for supply, soil, waste, drain, and vent lines.

A worm is a screw with a thread shaped like a rack tooth.

Proportions and shapes of gear teeth are not standardized.

Gears are used to transmit power and rotating or reciprocating motion from one machine part to another.

Bevel gear teeth have the same involute shape as teeth on spur gears but are tapered toward the cone apex.

Worm wheels are similar to helical gears cut to conform to the shape of the worm.

Working drawings for bevel gears give both the dimensions of the gear blank and the data necessary for cutting the teeth.

The motion of the follower as it rises or falls depends on the shape of the curves in the displacement diagram.

Teeth are spaced by laying out equal angles.

Structural steel is available in two standard shapes.

Structural steel shop drawings are usually calculated to the nearest inch.

One quick way to view the entire drawing area is to use the Zoom command by typing ________.

When setting up a mechanical drawing in AutoCAD the drafter should set the units to ________.

When drawing a line using the relative coordinate system a line is created from ________.

If you use the absolute coordinate system to create a line from a starting point of 0, 0 8 units on the X axis and 5 units on the Y axis you enter ________ for the second point.

Circles, circular arcs, and other curved surfaces may be drawn using offset measurements.

In general, all types of sections for isometric drawing may be applied to oblique drawing.

In an oblique drawing, when an angle is specified in degrees in a receding plane, you should convert the angle into circular measurements.

In CAD, oblique drawings are difficult to create because you cannot use snap increments or draw similarly to drawing on grid paper.

Many different types of wood are used as structural timber.

In order to set drawing limits for a "C" size architectural drawing the drafter should set the limits to ________.