

MCQOPTIONS
Saved Bookmarks
This section includes 410 Mcqs, each offering curated multiple-choice questions to sharpen your Surveying knowledge and support exam preparation. Choose a topic below to get started.
351. |
The type of surveying which requires least office work is |
A. | tacheomefry |
B. | trigonometrical levelling |
C. | plane table surveying |
D. | theodolite surveying |
Answer» D. theodolite surveying | |
352. |
The circle in which a plane tangent to the earth's surface at the point of observation, intersects the celestial sphere, is called |
A. | Visible horizon |
B. | Sensible horizon |
C. | Celestial horizon |
D. | True horizon |
Answer» C. Celestial horizon | |
353. |
The point on the celestial sphere vertically below the observer's position, is called |
A. | Zenith |
B. | Celestial point |
C. | Nadir |
D. | Pole |
Answer» D. Pole | |
354. |
In a tropical year, the numbers of sidereal days are |
A. | One less than mean solar days |
B. | One more than mean solar days |
C. | Equal to mean solar days |
D. | None of these |
Answer» C. Equal to mean solar days | |
355. |
Systematic errors |
A. | Always follow some definite mathematical law |
B. | Can be removed by applying corrections to the observed values |
C. | Are also known as cumulative errors |
D. | All the above |
Answer» E. | |
356. |
Theodolite is an instrument used for |
A. | tightening the capstan-headed nuts of level tube |
B. | measurement of horizontal angles only |
C. | measurement of vertical angles only |
D. | measurement of both horizontal and vertical angles |
Answer» E. | |
357. |
Cross staff is an instrument used for |
A. | measuring approximate horizontal angles |
B. | setting out right angles |
C. | measuring bearings of the lines |
D. | none of the above |
Answer» C. measuring bearings of the lines | |
358. |
Subtense bar is an instrument used for |
A. | levelling |
B. | measurement of horizontal distances in plane areas |
C. | measurement of horizontal distances in undulated areas |
D. | measurement of angles |
Answer» D. measurement of angles | |
359. |
The difference of levels between two stations A and B is to be determined. For best results, the instrument station should be |
A. | equidistant from A and B |
B. | closer to the higher station |
C. | closer to the lower station |
D. | as far as possible from the line AB |
Answer» B. closer to the higher station | |
360. |
The First Point of Aeries |
A. | Is the point in the celestial sphere where zero meridian crosses the celestial equator |
B. | Is usually denoted by the Greek letter ? |
C. | Is located near the very conspicuous rectangle of stars in the constellations of Pegasus and Andromeda |
D. | All the above |
Answer» E. | |
361. |
On vertical photographs, height displacement is |
A. | Positive for points above datum |
B. | Negative for points below datum |
C. | Zero for points vertically below the air station |
D. | All the above |
Answer» E. | |
362. |
In a spherical triangle ABC, right angled at C, sin b equals |
A. | sin a cos A |
B. | cos a sin A |
C. | tan a cot A |
D. | cot A tan a |
Answer» D. cot A tan a | |
363. |
If two points differing by 1° of latitude and of the same longitude is 110 km apart on the earth, then two astronomical positions on the moon is about |
A. | 10 km |
B. | 25 km |
C. | 30 km |
D. | 50 km |
Answer» D. 50 km | |
364. |
The want of correspondence in stereo-photographs |
A. | Is a good property |
B. | Is a function of tilt |
C. | Is not affected by the change of flying height between photographs |
D. | Is minimum when θ is 3° |
Answer» C. Is not affected by the change of flying height between photographs | |
365. |
The position of a heavenly body on the celestial sphere can be completely specified by |
A. | Its altitude and azimuth |
B. | Its declination and hour angle |
C. | Its declination and right ascension |
D. | All the above |
Answer» E. | |
366. |
If the lower clamp screw is tightened and upper clamp screw is loosened, the theodolite may be rotated |
A. | on its outer spindle with a relative motion between the vernier and graduated scale of lower plate |
B. | on its outer spindle without a relative motion between the vernier and gra-duated scale of lower plate |
C. | on its inner spindle with a relative motion between the vernier and the graduated scale of lower plate |
D. | on its inner spindle without a relative motion between the vernier and the graduated scale of lower plate |
Answer» D. on its inner spindle without a relative motion between the vernier and the graduated scale of lower plate | |
367. |
The process of determining the locations of the instrument station by drawing re sectors from the locations of the known stations is called |
A. | radiation |
B. | intersection |
C. | resection |
D. | traversing |
Answer» D. traversing | |
368. |
To have greatest coverage of the area, the type of photography used, is |
A. | High oblique |
B. | Low oblique |
C. | Vertical |
D. | None of these |
Answer» B. Low oblique | |
369. |
The parallax of a point on the photograph is due to |
A. | Ground elevation |
B. | Flying height |
C. | Length of air base |
D. | All the above |
Answer» E. | |
370. |
Polaris is usually observed for the determination of the latitude when it is |
A. | At culmination |
B. | At elongation |
C. | Neither at culmination nor at elongation |
D. | Either at culmination or at elongation |
Answer» B. At elongation | |
371. |
In a truly vertical photograph, |
A. | Principal point coincides the isocenter |
B. | Iso-centre coincides the plumb point |
C. | Plumb point coincides the principal point |
D. | All the above |
Answer» E. | |
372. |
With standard meridian as 82° 30' E the standard time at longitude 90° E is 8 h 30 m. The local mean time at the place will be |
A. | 7 h 00 m |
B. | 7 h 30 m |
C. | 8 h 00 m |
D. | 9 h 00 m |
Answer» E. | |
373. |
The displacement of the pictured position of a point of h elevation on a vertical photograph taken with a camera of 30 cm focal length, from an altitude of 3000 m, is |
A. | 4.4 mm |
B. | 5.5 mm |
C. | 6.5 mm |
D. | 7.5 mm |
Answer» E. | |
374. |
A star may culminate at zenith if its declination is |
A. | Greater than the longitude of the place |
B. | Less than the latitude of the place |
C. | Equal to the latitude of the place |
D. | None of these |
Answer» D. None of these | |
375. |
Horizontal distances obtained by thermometric observations |
A. | require slope correction |
B. | require tension correction |
C. | require slope and tension corrections |
D. | do not require slope and tension corrections |
Answer» E. | |
376. |
Which of the following methods of theodolite traversing is suitable for locating the details which are far away from transit stations? |
A. | Measuring angle and distance from one transit station |
B. | Measuring angles to the point from at least two stations |
C. | Measuring angle at one station and distance from other |
D. | Measuring distance from two points on traverse line |
Answer» C. Measuring angle at one station and distance from other | |
377. |
For any star to be a circumpolar star, its |
A. | Declination must be 0° |
B. | Declination must be 90° |
C. | Distance from the pole must be less than the latitude of the observer |
D. | Hour angle must be 180° |
Answer» D. Hour angle must be 180° | |
378. |
The adjustment of horizontal cross hair is required particularly when the instrument is used for |
A. | leveling |
B. | prolonging a straight line |
C. | measurement of horizontal angles |
D. | all of the above |
Answer» B. prolonging a straight line | |
379. |
Bowditch rule is applied to |
A. | an open traverse for graphical adjustment |
B. | a closed traverse for adjustment of closing error |
C. | determine the effect of local attraction |
D. | none of the above |
Answer» C. determine the effect of local attraction | |
380. |
A Nautical mile is |
A. | One minute arc of the great circle passing through two points |
B. | One minute arc of the longitude |
C. | 1855.109 m |
D. | All the above |
Answer» E. | |
381. |
Local attraction in compass surveying may exist due to |
A. | incorrect levelling of the magnetic needle |
B. | loss of magnetism of the needle |
C. | friction of the needle at the pivot |
D. | presence of magnetic substances near the instrument |
Answer» E. | |
382. |
Which of the following is not the function of levelling head ? |
A. | to support the main part of the instrument |
B. | to attach the theodolite to the tripod |
C. | to provide a means for leveling the theodolite |
D. | none of the above |
Answer» E. | |
383. |
In an internal focussing type of telescope, the lens provided is |
A. | concave |
B. | convex |
C. | plano-convex |
D. | plano-concave |
Answer» B. convex | |
384. |
The scale of the photography taken from a height of 300 m, with a camera of focal length 15 cm, is |
A. | 1 : 10,000 |
B. | 1 : 15,000 |
C. | 1 : 20,000 |
D. | 1 : 30,000 |
Answer» D. 1 : 30,000 | |
385. |
The rate of change of parallax dp/dh with respect to change in h, may be expressed as |
A. | fB/(H - h) |
B. | fB/(H - h)² |
C. | fB/(H + h) |
D. | fB/(H + h)² |
Answer» C. fB/(H + h) | |
386. |
The position of the sun when its north declination is maximum is known as |
A. | Vernal equinox |
B. | Autumnal equinox |
C. | Summer solstice |
D. | Winter solstice |
Answer» D. Winter solstice | |
387. |
The prismatic compass and surveyor’s compass |
A. | give whole circle bearing (WCB) of a line and quadrantal bearing (QB) of a line respectively |
B. | both give QB of a line and WCB of a line |
C. | both give QB of a line |
D. | both give WCB of a line |
Answer» B. both give QB of a line and WCB of a line | |
388. |
If a tripod settles in the interval that elapses between taking a back sight reading and the following foresight reading, then the elevation of turning point will |
A. | increase |
B. | decrease |
C. | not change |
D. | either ‘A’ or ‘B’ |
Answer» B. decrease | |
389. |
The sidereal day is the time interval between two successive upper transits of |
A. | Mean sun |
B. | First point of Aries |
C. | First point of Libra |
D. | The polar star |
Answer» C. First point of Libra | |
390. |
Longitude of a place is the angular distance between the meridian of the place and |
A. | The standard meridian |
B. | The International Date Line |
C. | That of Greenwich |
D. | Both (A) and (C) of above |
Answer» E. | |
391. |
The shortest distance between two places measured along the surface of the earth, is |
A. | Length of the equator between their longitudes |
B. | Length of the parallel between their longitudes |
C. | Length of the arc of the great circle passing through them |
D. | None of these |
Answer» D. None of these | |
392. |
The correction applied to the measured base of length ‘L’ is |
A. | Tension = (P - Ps)L/AE |
B. | Sag = L³w²/24P² where w is the weight of tape/m |
C. | Slope = (h²/2L) + (h⁴/8L³) where h is height difference of end supports |
D. | All the above |
Answer» E. | |
393. |
Direct method of contouring is |
A. | a quick method |
B. | adopted for large surveys only |
C. | most accurate method |
D. | suitable for hilly terrains |
Answer» D. suitable for hilly terrains | |
394. |
With the rise of temperature, the sensitivity of a bubble tube |
A. | decreases |
B. | increases |
C. | remains unaffected |
D. | none of the above |
Answer» B. increases | |
395. |
Polaris is usually observed for the determination of the azimuth when it is |
A. | At culmination |
B. | At elongation |
C. | Neither at culmination nor at elongation |
D. | Either at culmination or at elongation |
Answer» C. Neither at culmination nor at elongation | |
396. |
If the general ground level of any area is 10% of the flying height, the principal points may be used as the centers of radial directions for small scale mapping even in tilted photograph up to |
A. | 1° |
B. | 2° |
C. | 3° |
D. | 4° |
Answer» D. 4° | |
397. |
For plane ground the scale of a vertical photograph will be same as that of a tiled photograph along the photo parallel through |
A. | Isocenter |
B. | Plumb point |
C. | Principal point |
D. | None of these |
Answer» B. Plumb point | |
398. |
Triangulation surveys are carried out for locating |
A. | Control points for surveys of large areas |
B. | Control points for photogrammetric surveys |
C. | Engineering works, i.e. terminal points of long tunnels, bridge abutments, etc. |
D. | All the above |
Answer» E. | |
399. |
The altitudes of a circumpolar star at culminations are 70° and 10°, both culminations being north of zenith. The latitude of the place, is |
A. | 80° |
B. | 70° |
C. | 60° |
D. | 40° |
Answer» E. | |
400. |
If the altitudes of a star at its upper and lower transits are 60° 30' and 19° 30' respectively, the latitude of the place, is |
A. | 30° |
B. | 35° |
C. | 30° |
D. | 45° |
Answer» D. 45° | |