

MCQOPTIONS
Saved Bookmarks
This section includes 246 Mcqs, each offering curated multiple-choice questions to sharpen your Chemical Engineering knowledge and support exam preparation. Choose a topic below to get started.
51. |
The coking process normally mostly used in Indian oil refineries is the ____________________ coking process ? |
A. | Delayed |
B. | Flexi |
C. | Fluid |
D. | Contact |
Answer» B. Flexi | |
52. |
The characterisation factor of a crude oil is calculated as 12.5. It means that; it is________________? |
A. | Paraffinic |
B. | Naphthenic |
C. | Intermediate |
D. | None of these |
Answer» B. Naphthenic | |
53. |
The characterisation factor of crude petroleum oil is around__________________? |
A. | 3 |
B. | 11 |
C. | 22 |
D. | 28 |
Answer» C. 22 | |
54. |
The catalytic cracking of heavier petroleum fraction is done to produce mainly____________________? |
A. | Gasoline |
B. | Asphalt |
C. | Diesel oil |
D. | Tar |
Answer» D. Tar | |
55. |
The best method of determining sulphur in crude oil is by the _______________ method? |
A. | Kjeldahl |
B. | Dumas |
C. | Bomb calorimeter |
D. | Junkers calorimeter |
Answer» D. Junkers calorimeter | |
56. |
The average boiling point of aviation turbine fuel is closest to that of__________________? |
A. | Lubricating oils |
B. | LPG |
C. | Diesel |
D. | Kerosene |
Answer» E. | |
57. |
The amount of tetraethyl lead added to improve the octane number of motor gasoline is around ______________ c.c per gallon of petrol? |
A. | 3 |
B. | 300 |
C. | 3000 |
D. | 1000 |
Answer» B. 300 | |
58. |
Salt content (measured as sodium chloride) in electrically desalted crude oil comes down to a level of about __________________ ptb (pounds per thousand barrel) ? |
A. | 0.03 |
B. | 3 |
C. | 35 |
D. | 70 |
Answer» C. 35 | |
59. |
Road grade bitumen is produced from vacuum residue by its ____________________? |
A. | Aeration |
B. | Pyrolysis |
C. | Hydrogenation |
D. | Steam reforming |
Answer» E. | |
60. |
Research octane number refers to the___________________? |
A. | Low octane number motor fuels |
B. | High octane number motor fuels |
C. | High octane number aviation fuels |
D. | Unleaded motor fuels |
Answer» E. | |
61. |
Removal of light fractions from crude oil is called its _____________________? |
A. | Sweetening |
B. | Dehydration |
C. | Stabilisation |
D. | Visbreaking |
Answer» D. Visbreaking | |
62. |
Reid vapour pressure of gasoline is the measure of its_________________? |
A. | Pour point |
B. | Cloud point |
C. | Vapour locking tendency |
D. | Carbon residue |
Answer» D. Carbon residue | |
63. |
Refractive index of a petrofuel which is the ratio of velocity of light in air to its velocity in the petrofuel gives an indication if its_________________? |
A. | Molecular weight |
B. | Aromatics content |
C. | Both A. & B. |
D. | Neither ‘a’ nor ‘b’ |
Answer» D. Neither ‘a’ nor ‘b’ | |
64. |
Reforming__________________? |
A. | Uses naphtha as feedstock |
B. | Does not much affect the molecular weight of the feed |
C. | Improves the quality & yield of gasoline |
D. | All A., B. and C. |
Answer» E. | |
65. |
Reforming converts_________________? |
A. | Olefins into paraffins |
B. | Naphthenes into aromatics |
C. | Naphthenes into olefins |
D. | Naphthenes into paraffin |
Answer» C. Naphthenes into olefins | |
66. |
Raw Kerosene has a smoke point of 15 mm. After it is subjected to dearomatization by liquid SO2 extraction (Edeleanu process), its smoke point may become _______________________ mm? |
A. | 5 |
B. | 10 |
C. | 25 |
D. | 100 |
Answer» D. 100 | |
67. |
Quinoline is a/an ________________ compound ? |
A. | Sulphur |
B. | Nitrogen |
C. | Oxygen |
D. | None of these |
Answer» C. Oxygen | |
68. |
Pyrolysis of kerosene or natural gasoline is done to produce mainly the___________________? |
A. | Olefins and aromatics |
B. | Lighter paraffins |
C. | Stabilised gasoline |
D. | Diesel |
Answer» B. Lighter paraffins | |
69. |
Products drawn from the top to bottom of the crude oil distillation column has progressively increasing ___________________? |
A. | Boiling points |
B. | Molecular weight |
C. | C/H ratio |
D. | All A., B. and C. |
Answer» E. | |
70. |
Pressure & temperature maintained in catalytic cracking is about__________________? |
A. | 2 atm & 500°C |
B. | 10 atm & 500°C |
C. | 30 atm & 200°C |
D. | 50 atm & 750°C |
Answer» B. 10 atm & 500°C | |
71. |
Pressure maintained in the high pressure primary tower of a three stage crude oil distillation system is about ______________ kg/cm2? |
A. | 1.5 |
B. | 3 |
C. | 6 |
D. | 12 |
Answer» C. 6 | |
72. |
Presence of sulphur in gasoline___________________? |
A. | Leads to corrosion |
B. | Increases lead susceptibility |
C. | Decreases gum formation |
D. | Helps during stabilisation |
Answer» B. Increases lead susceptibility | |
73. |
Presence of predominantly large quantity of aromatics (polynuclear) is not desirable in aviation fuel, because it has__________________? |
A. | High pour point and low smoke point |
B. | Low viscosity index |
C. | High self-ignition temperature |
D. | All A., B. and C. |
Answer» C. High self-ignition temperature | |
74. |
Presence of aromatics in __________________? |
A. | Diesel increases its cetane number |
B. | Kerosene increases its smoke point |
C. | Petrol increases its octane number |
D. | All A., B. and C. |
Answer» D. All A., B. and C. | |
75. |
Preheating temperature of medium viscosity furnace oil for better atomisation through burner is about _______________ °C ? |
A. | 50 |
B. | 70 |
C. | 90 |
D. | 140 |
Answer» D. 140 | |
76. |
Pour point of a petrofuel is________________? |
A. | Multiple of 3°F |
B. | Multiple of 5°F |
C. | 5°C below the temperature at which oil ceases to flow |
D. | None of these |
Answer» D. None of these | |
77. |
Pour point and freezing point is equal for__________________? |
A. | Petrol |
B. | Diesel |
C. | Water |
D. | Crude petroleum |
Answer» D. Crude petroleum | |
78. |
Polymerisation__________________? |
A. | Produces i-octane from cracked gases containing i-butane and butene |
B. | Causes olefins to combine with each other |
C. | Causes aromatics to combine with each other |
D. | Is aimed at producing lubricating oil |
Answer» C. Causes aromatics to combine with each other | |
79. |
Platforming is a ____________ process? |
A. | Moving bed |
B. | Fluidised bed |
C. | Non-regenerative & fixed bed |
D. | Regenerative |
Answer» D. Regenerative | |
80. |
Pick out the wrong statement about the smoking tendency of various hydrocarbon constituents of kerosene ? |
A. | Smoking tendency of hydrocarbons increases in the order: paraffins → isoparaffins → naphthenes → aromatics |
B. | Smoking tendency of paraffins increases with decrease in its molecular weight |
C. | Smoking tendency of naphthenes decreases with its increasing molecular weight & also on addition of double bond |
D. | Smoking tendency of aromatics decreases with increase in its molecular weight |
Answer» C. Smoking tendency of naphthenes decreases with its increasing molecular weight & also on addition of double bond | |
81. |
Pick out the undesirable property for a solvent meant for dewaxing of lube oil ? |
A. | Complete miscibility with oil |
B. | High solubility of wax in the solvent |
C. | Both A. and B. |
D. | Neither A. nor B. |
Answer» D. Neither A. nor B. | |
82. |
Pick out the correct statement pertaining to catalytic cracking ? |
A. | With increase in the reactor pressure, octane number of gasoline decreases |
B. | With increase in the reactor temperature, gasoline yield decreases for a given conversion |
C. | Percentage conversion increases with increase in the catalyst to oil ratio |
D. | All A., B. and C. |
Answer» E. | |
83. |
Pick out the correct statement about catalytic polymerisation ? |
A. | H2SO4 polymerisation process gives gasoline rich in unsaturates |
B. | In H2SO4 polymerisation, H3PO4 is always used with 2% steam to prevent meta & ortho H3PO4 formation, which are inactive |
C. | Both A. and B. |
D. | Neither A. nor B. |
Answer» C. Both A. and B. | |
84. |
Pick out the additive property of lube oil out of following ? |
A. | °API gravity |
B. | Specific gravity |
C. | Viscosity |
D. | Flashpoint |
Answer» B. Specific gravity | |
85. |
Phenols are added in gasoline to____________________? |
A. | Improve the octane number |
B. | Act as an antioxidant |
C. | Reduce its viscosity |
D. | Increase its pour point |
Answer» C. Reduce its viscosity | |
86. |
Petroleum ________________ ? |
A. | Is optically active |
B. | Constitutes mainly of olefins |
C. | Does not contain asphalt |
D. | Does not contain aromatics |
Answer» B. Constitutes mainly of olefins | |
87. |
Petroleum coke is used mainly in the __________________ ? |
A. | Discoloration of yellow glycerine |
B. | Sugar refining |
C. | Manufacture of carbon electrode |
D. | Blast furnace for reduction of iron ore |
Answer» D. Blast furnace for reduction of iron ore | |
88. |
Petroleum is believed to have originated from _______________ sources? |
A. | Vegetable |
B. | Animal |
C. | Both A. and B. |
D. | Neither A. nor B. |
Answer» D. Neither A. nor B. | |
89. |
Petrolatum is__________________? |
A. | Same as petroleum ether |
B. | Petroleum coke |
C. | A mixture of microcrystalline wax in viscous hydrocarbon liquids |
D. | None of these |
Answer» D. None of these | |
90. |
Performance number of a liquid fuel is related to its __________________? |
A. | Wax content |
B. | Spontaneous ignition temperature |
C. | Knocking tendency |
D. | Sulphur content |
Answer» C. Knocking tendency | |
91. |
Percentage of straight run gasoline in a typical crude oil may be around________________? |
A. | 6 |
B. | 18 |
C. | 38 |
D. | 52 |
Answer» E. | |
92. |
Penetration test determines the _____________ of the grease? |
A. | Stiffness |
B. | Lubricating properties (e.g. oilness) |
C. | Service temperature |
D. | Variation in viscosity with temperature |
Answer» B. Lubricating properties (e.g. oilness) | |
93. |
Paraffins are desirable in lubricating oil, as it has got high_____________________? |
A. | Viscosity |
B. | Viscosity index |
C. | Smoke point |
D. | Pour point |
Answer» D. Pour point | |
94. |
Paraffin base crude oil as compared to asphalt base crude gives___________________? |
A. | Higher yield of straight run gasoline |
B. | Higher octane number gasoline |
C. | Lower viscosity index lube oil |
D. | Poorer yield of lube oil |
Answer» B. Higher octane number gasoline | |
95. |
Operating temperature and pressure in catalytic reforming is about_____________? |
A. | 1-5 Kgf/cm2 & 200°C |
B. | 15-45 Kgf/cm2 & 450-550°C |
C. | 50 – 75 kgf/cm2 & 600 – 800°C |
D. | 5-10 kgf/cm2 & 150 – 250°C |
Answer» C. 50 – 75 kgf/cm2 & 600 – 800°C | |
96. |
Operating condition in the electrical dehydrators for crude oil is about____________________? |
A. | 6.5 kgf/Cm2 & 95°C |
B. | 1 atm. & 110 °C |
C. | 20 kgf/cm2 & 110°C |
D. | 50 atm. and 150°C |
Answer» B. 1 atm. & 110 °C | |
97. |
Olefins are_________________? |
A. | Saturated hydrocarbons |
B. | Unsaturated cyclic compounds (hydrocarbons) |
C. | Present in substantially good quantity in crude petroleum |
D. | None of these |
Answer» E. | |
98. |
Older crude petroleum __________________? |
A. | Is light and better |
B. | Gives more distillates |
C. | Gives less tar |
D. | All A., B. and C. |
Answer» C. Gives less tar | |
99. |
Octane number (unleaded) of gasoline produced by isomerisation of butane may be about __________________? |
A. | 45 |
B. | 55 |
C. | 70 |
D. | 90 |
Answer» D. 90 | |
100. |
Octane numbers of motor gasoline used in India and America are respectively________________? |
A. | 87 & 94 |
B. | 94 & 87 |
C. | 94 & 100 |
D. | 83 & 100 |
Answer» B. 94 & 87 | |