MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 97 Mcqs, each offering curated multiple-choice questions to sharpen your Computer Science Engineering (CSE) knowledge and support exam preparation. Choose a topic below to get started.
| 51. |
Which of the following is used as storage locations both in the ALU and the control section of a computer ? |
| A. | accumulator |
| B. | register |
| C. | adder |
| D. | decoder |
| Answer» C. adder | |
| 52. |
The register which contains the data to be written into or read out of the addressed location is called |
| A. | memory address register |
| B. | memory data register |
| C. | program counter |
| D. | index register |
| Answer» C. program counter | |
| 53. |
The register which holds the address of the location to or from which data are to be transferred is called |
| A. | index register |
| B. | instruction register |
| C. | memory address register |
| D. | memory data register |
| Answer» D. memory data register | |
| 54. |
The stack pointer in the microprocessor is a |
| A. | 16 bit register that point to stack |
| B. | 32 bit accumulator |
| C. | memory location in the stack |
| D. | flag register used for the stack |
| Answer» B. 32 bit accumulator | |
| 55. |
Which processor provided 1 MB memory: |
| A. | 16-bit 8086 and 8088 |
| B. | 32-bit 8086 and 8088 |
| C. | 64-bit 8086 and 8088 |
| D. | 8-bit 8086 and 8088 |
| Answer» B. 32-bit 8086 and 8088 | |
| 56. |
How many speed of 8088,8085,8086 microprocessor: |
| A. | 2.5 million instruction per second |
| B. | 1.5 million instruction per second |
| C. | 3.5 million instruction per second |
| D. | 1.6 million instruction per second |
| Answer» B. 1.5 million instruction per second | |
| 57. |
Which is 16 Bit microprocessor: |
| A. | 8088 |
| B. | 8086 |
| C. | 8085 |
| D. | all of these |
| Answer» E. | |
| 58. |
ADC 0809 IS A ----- PIN IC |
| A. | 40 |
| B. | 20 |
| C. | 24 |
| D. | 28 |
| Answer» E. | |
| 59. |
Conversion time of ADC 0808 IS |
| A. | 100 ms |
| B. | 100micro sec |
| C. | 100 ms |
| D. | 100ns |
| Answer» C. 100 ms | |
| 60. |
Conversion time Tc of successive approximation ADC is given as |
| A. | t(n-1) |
| B. | t(n+1) |
| C. | t(n) |
| D. | t(n+2) |
| Answer» C. t(n) | |
| 61. |
Whichof the following is the fastest ADC |
| A. | dual slope |
| B. | successive approximation |
| C. | flash |
| D. | single slope |
| Answer» D. single slope | |
| 62. |
Upon activation of------ signal,output device reads data from output port and acknowledges it |
| A. | intr |
| B. | ack\ |
| C. | obf\ |
| D. | ibf |
| Answer» D. ibf | |
| 63. |
To indicate end of conversion ADC 0808/0809 ACTIVATES -----SIGNAL |
| A. | eoc |
| B. | soc |
| C. | clk |
| D. | output control |
| Answer» B. soc | |
| 64. |
Asynchronous serial communication involves transmission of |
| A. | start bit |
| B. | stop bit |
| C. | character data |
| D. | all |
| Answer» E. | |
| 65. |
8255 sets INTR when STB'=-----,IBF=---------,INTE=--------,for input conrol signals |
| A. | 1,0,1 |
| B. | 1,1,0 |
| C. | 1,1,1 |
| D. | 0,1,1 |
| Answer» D. 0,1,1 | |
| 66. |
Walkie-talkie is an example of serial communication |
| A. | simplex |
| B. | half-duplex |
| C. | full-duplex |
| D. | none |
| Answer» C. full-duplex | |
| 67. |
In ------ of 8255 ,bidirectionali/o data transfer is possible |
| A. | mode0 |
| B. | mode1 |
| C. | mode2 |
| D. | bsr mode |
| Answer» D. bsr mode | |
| 68. |
IBF is an active-------- output signal for 8255 |
| A. | high |
| B. | low |
| C. | enable |
| D. | disable |
| Answer» B. low | |
| 69. |
On activation of --------,8255 loads data from the input port lines into the input buffer of that port |
| A. | stb\ |
| B. | ibf |
| C. | obf\ |
| D. | none |
| Answer» C. obf\ | |
| 70. |
For i/o mode of 8255 ,if -----, the word is taken as a bit set/reset word |
| A. | d7=1 |
| B. | d7=0 |
| C. | d0=1 |
| D. | d0=0 |
| Answer» C. d0=1 | |
| 71. |
A high on ----pin causes all 24 lines of three 8 bit ports to be in the input mode |
| A. | wr\ |
| B. | reset |
| C. | gnd |
| D. | vcc |
| Answer» C. gnd | |
| 72. |
For i/o mode of 8255,if -----,the word is taken as a mode definition word |
| A. | d7=1 |
| B. | d7=0 |
| C. | d0=1 |
| D. | d0=0 |
| Answer» B. d7=0 | |
| 73. |
8255 has ----i/o modes |
| A. | 2 |
| B. | 3 |
| C. | 4 |
| D. | 8 |
| Answer» C. 4 | |
| 74. |
BSR mode is used to set or reset the bitsin |
| A. | porta |
| B. | portb |
| C. | portc |
| D. | portd |
| Answer» D. portd | |
| 75. |
In 8255 ,BSR means ----- |
| A. | bit set/reset |
| B. | byteset/reset |
| C. | binary set/reset |
| D. | none |
| Answer» B. byteset/reset | |
| 76. |
8255 has three ----parallel ports |
| A. | 8 bit |
| B. | 16 bit |
| C. | 32 bit |
| D. | 64 bit |
| Answer» B. 16 bit | |
| 77. |
8255 has -------- i/o pins |
| A. | 28 |
| B. | 26 |
| C. | 24 |
| D. | 22 |
| Answer» D. 22 | |
| 78. |
ADC 0808 operates on single ---- power supply |
| A. | 5v |
| B. | 10v |
| C. | 15v |
| D. | 20v |
| Answer» B. 10v | |
| 79. |
EOC means |
| A. | end of conversion |
| B. | enable output conversion |
| C. | error of conversion |
| D. | none of these |
| Answer» B. enable output conversion | |
| 80. |
ADC 0808 is ----- pin IC |
| A. | 40 |
| B. | 20 |
| C. | 24 |
| D. | 28 |
| Answer» E. | |
| 81. |
for mode 3 of 8253/54, if the count is odd the output will be high for--- |
| A. | 2/(n+1) |
| B. | (n+1)/2 |
| C. | 2/(n-1) |
| D. | (n-1)/2 |
| Answer» C. 2/(n-1) | |
| 82. |
8253/54 has c----command that allows the user to check the count value programmed mode and current status of the counter |
| A. | write back |
| B. | write ahead |
| C. | read ahead |
| D. | read back |
| Answer» E. | |
| 83. |
in mode 0 of 8253/54 ----disables counting |
| A. | gate=1 |
| B. | gate=0 |
| C. | wr#=1 |
| D. | wr#=0 |
| Answer» C. wr#=1 | |
| 84. |
8253/54 timers can be programmed in---modes |
| A. | 1 |
| B. | 3 |
| C. | 6 |
| D. | 5 |
| Answer» D. 5 | |
| 85. |
8253/54 has ----independent timers/counters |
| A. | 1 |
| B. | 2 |
| C. | 3 |
| D. | 4 |
| Answer» D. 4 | |
| 86. |
Flash ADC consist of….converters |
| A. | 2^n |
| B. | 2^n -1 |
| C. | 2^n +1 |
| D. | none of these |
| Answer» C. 2^n +1 | |
| 87. |
Adc 0808 uses ----technique |
| A. | successive apraximation |
| B. | single step |
| C. | dual slope |
| D. | flash converter |
| Answer» B. single step | |
| 88. |
A high on ---line indicates that the buffer register is empty |
| A. | txrdy |
| B. | txe |
| C. | txc# |
| D. | both b and c |
| Answer» C. txc# | |
| 89. |
to configure 8255 with port A output,Port B input port C lower output and port C upper input |
| A. | mov al,0afh |
| B. | mov al,0aeh |
| C. | mov al,0ceh |
| D. | mov a,0aah |
| Answer» C. mov al,0ceh | |
| 90. |
the signals provided by ADC are |
| A. | soc |
| B. | eoc |
| C. | ale |
| D. | all of these |
| Answer» E. | |
| 91. |
Asynchronous serial communication involves |
| A. | start bit |
| B. | stop bits |
| C. | character data |
| D. | all of these |
| Answer» E. | |
| 92. |
Transmission through telephone lines is an example of….serial commuincation |
| A. | simplex |
| B. | half duplex |
| C. | full duplex |
| D. | none of these |
| Answer» D. none of these | |
| 93. |
8255 has three ----parrallel port |
| A. | 8bit |
| B. | 16bit |
| C. | 32bit |
| D. | 64bit |
| Answer» B. 16bit | |
| 94. |
on activation of ----, 8255 loads data from the input port lines into the input buffer of that port |
| A. | stb# |
| B. | ibf |
| C. | obf# |
| D. | none of these |
| Answer» C. obf# | |
| 95. |
in ----, bidirectional data transfer is possible |
| A. | mode 0 |
| B. | mode1 |
| C. | mode2 |
| D. | bsr |
| Answer» D. bsr | |
| 96. |
walkie-talkie is an example of …..serial communication |
| A. | simplex |
| B. | half duplex |
| C. | full duplex |
| D. | none of these |
| Answer» C. full duplex | |
| 97. |
for i/o of 8255,if -----, the word is taken as a bit set/rest word |
| A. | d7=1 |
| B. | d7=0 |
| C. | d0=1 |
| D. | d0=0 |
| Answer» C. d0=1 | |