MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 26 Mcqs, each offering curated multiple-choice questions to sharpen your Machine Drawing knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
For a cylinder, minimum views required for describing the shape are ____________ |
| A. | Three |
| B. | Two |
| C. | One |
| D. | Four |
| Answer» C. One | |
| 2. |
Side view is drawn by viewing from either the left or right side, whichever is __________ |
| A. | Easy to read |
| B. | Suitable to draw |
| C. | Having longest dimensions |
| D. | More informative |
| Answer» E. | |
| 3. |
A pictorial view must show __________ of a machine. |
| A. | All the details necessary for its construction |
| B. | The outside appearance |
| C. | True shape of the machine |
| D. | All the faces of the machine |
| Answer» C. True shape of the machine | |
| 4. |
The principal plane chosen in an orthographic view of a machine drawing is/are ______ |
| A. | Horizontal, vertical and side plane |
| B. | Horizontal and side plane only |
| C. | Vertical and horizontal plane only |
| D. | Only vertical plane |
| Answer» B. Horizontal and side plane only | |
| 5. |
A designer is looking to draw the side view of a car in perspective, which of the below given choice is the best? |
| A. | Choosing vanishing points in the paper area |
| B. | Choosing a single vanishing point at infinity |
| C. | Choosing a three-point perspective |
| D. | Choosing an orthographic view |
| Answer» C. Choosing a three-point perspective | |
| 6. |
Projectors are referred to______________ |
| A. | Plane of projection |
| B. | Picture plane |
| C. | Rays intersecting the corner and edges of the object |
| D. | Line of site |
| Answer» D. Line of site | |
| 7. |
Which type of view best describes the view, of the below given figure? |
| A. | Oblique View |
| B. | Perspective View |
| C. | Axonometric View |
| D. | Orthographic View |
| Answer» C. Axonometric View | |
| 8. |
Which type of view is shown in the below figure? |
| A. | Oblique View |
| B. | Perspective View |
| C. | Axonometric View |
| D. | Orthographic View |
| Answer» B. Perspective View | |
| 9. |
The figure shown below depicts which type of view? |
| A. | Oblique View |
| B. | Perspective View |
| C. | Axonometric View |
| D. | Orthographic View |
| Answer» D. Orthographic View | |
| 10. |
In an axonometric view, line of site are ______________ |
| A. | Perpendicular to plane of projection with all three faces equally inclined to picture plane |
| B. | Perpendicular to plane of projection with all three faces need not be equally inclined to picture plane |
| C. | Inclined to the plane of projection at certain angle |
| D. | One face of the object needs to be parallel |
| Answer» C. Inclined to the plane of projection at certain angle | |
| 11. |
A_DESIGNER_IS_LOOKING_TO_DRAW_THE_SIDE_VIEW_OF_A_CAR_IN_PERSPECTIVE,_WHICH_OF_THE_BELOW_GIVEN_CHOICE_IS_THE_BEST??$ |
| A. | Choosing vanishing points in the paper area |
| B. | Choosing a single vanishing point at infinity |
| C. | Choosing a three-point perspective |
| D. | Choosing an orthographic view |
| Answer» C. Choosing a three-point perspective | |
| 12. |
A pictorial view must show __________ of a machine.$ |
| A. | All the details necessary for its construction |
| B. | The outside appearance |
| C. | True shape of the machine |
| D. | All the faces of the machine |
| Answer» C. True shape of the machine | |
| 13. |
The_principal_plane_chosen_in_an_orthographic_view_of_a_machine_drawing_is/are_______$ |
| A. | Horizontal, vertical and side plane |
| B. | Horizontal and side plane only |
| C. | Vertical and horizontal plane only |
| D. | Only vertical plane |
| Answer» B. Horizontal and side plane only | |
| 14. |
_______ is an object seen by a human eye. |
| A. | Perspective view |
| B. | Axonometric view |
| C. | Orthogonal view |
| D. | Isometric view |
| Answer» B. Axonometric view | |
| 15. |
Which of the following is not a subtype of pictorial view? |
| A. | Cabinet view |
| B. | Auxiliary section view |
| C. | Cavalier view |
| D. | 3 vanishing point view |
| Answer» C. Cavalier view | |
| 16. |
While drawing an object on paper, which of the following method is not suitable regarding to its size? |
| A. | Enlarge suitably if it is too small |
| B. | Reduce if it is bigger than the paper size |
| C. | Always should be drawn of the same size |
| D. | Drawn of the same size if it can be accommodated on the paper |
| Answer» D. Drawn of the same size if it can be accommodated on the paper | |
| 17. |
Sectional views can be drawn to show the ____________ |
| A. | Hatching lines |
| B. | Outside views |
| C. | Internal details |
| D. | Symmetric objects |
| Answer» D. Symmetric objects | |
| 18. |
Single view may be enough to describe the shape of _______ |
| A. | Thick objects |
| B. | Thin objects |
| C. | Symmetric objects |
| D. | Vertical objects |
| Answer» C. Symmetric objects | |
| 19. |
The method of ________ projection is universally adopted for the purpose of engineering drawing. |
| A. | Orthographic |
| B. | Isometric |
| C. | Oblique |
| D. | Perspective |
| Answer» B. Isometric | |
| 20. |
In perspective view, the object can be inclined at ______ angle. |
| A. | 300 |
| B. | 450 |
| C. | 600 |
| D. | Any |
| Answer» E. | |
| 21. |
Side_view_is_drawn_by_viewing_from_either_the_left_or_right_side,_whichever_is___________ |
| A. | Easy to read |
| B. | Suitable to draw |
| C. | Having longest dimensions |
| D. | More informative |
| Answer» E. | |
| 22. |
Projectors are referred to_____________? |
| A. | Plane of projection |
| B. | Picture plane |
| C. | Rays intersecting the corner and edges of the object |
| D. | Line of site |
| Answer» D. Line of site | |
| 23. |
In which of the below given views, the picture plane is the same as the plane of the projection? |
| A. | Pictorial view |
| B. | Perspective view |
| C. | Orthographic view |
| D. | Oblique view |
| Answer» D. Oblique view | |
| 24. |
In which of the following view the vanishing point is assumed to be located at infinity? |
| A. | Perspective view |
| B. | Orthographic view |
| C. | Axonometric view |
| D. | Perspective with one face of object parallel to the plane of picture |
| Answer» D. Perspective with one face of object parallel to the plane of picture | |
| 25. |
In an axonometric view, line of site are ______________ |
| A. | Perpendicular to plane of projection with all three faces equally inclined to picture plane |
| B. | Perpendicular to plane of projection with all three faces need not be equally inclined to picture plane |
| C. | Inclined to the plane of projection at certain angle |
| D. | One face of the object needs to be parallel |
| Answer» C. Inclined to the plane of projection at certain angle | |
| 26. |
Axonometric view is a type of _____________ |
| A. | Orthographic view |
| B. | Pictorial view |
| C. | Oblique View |
| D. | Pictorial and Oblique View |
| Answer» C. Oblique View | |