What does the command provide?

It is used to enter ROM Monitor mode.

It is used to restart the router.

It is used to bypass the configuration in NVRAM.

It is used to enter ROM Monitor mode.

It is used to view the lost password.

You need to gather the IP address of a remote switch that is located in Hawaii. What can you do to find the address?

Issue the show ip arp command on the router connected to the switch.

Issue the show ip route command on the router connected to the switch.

Issue the show cdp neighbor command on the router connected to the switch.

Issue the show cdp neighbors detail command on the router connected to the switch.

The configuration register setting of 0x2102 provides what function to a router?

Boots the IOS from a TFTP server

Tells the router to boot into ROM monitor mode

Tells the router to look in NVRAM for the boot sequence

Boots the IOS from a TFTP server

What does the command o/r 0x2142 provide?

It is used to enter ROM Monitor mode.

It is used to restart the router.

It is used to bypass the configuration in NVRAM.

It is used to enter ROM Monitor mode.

It is used to view the lost password.

You telnet into a remote device and type debug ip rip, but no output from the debug command is seen. What could the problem be?

Debug output is sent only to the console.

You must type the show ip rip command first.

IP addressing on the network is incorrect.

You must use the terminal monitor command.

Debug output is sent only to the console.

You copy a configuration from a network host to a router's RAM. The configuration looks correct, yet it is not working at all. What could the problem be?

The IOS became corrupted after the copy command was initiated.

You copied the wrong configuration into RAM.

You copied the configuration into flash memory instead.

The copy did not override the shutdown command in running-config.

The IOS became corrupted after the copy command was initiated.

You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?

The newly upgraded IOS is not compatible with the hardware of the router.

You didn't boot the router with the correct command.

The configuration register setting is incorrect.

The newly upgraded IOS is not compatible with the hardware of the router.

The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?

The new configuration should be entered and saved.

RAM should be erased and the router restarted.

Flash should be erased and the router restarted.

NVRAM should be erased and the router restarted.

The new configuration should be entered and saved.

26 + Mcqs in Managing A Cisco Internetwork in Networking Page 1 McqOptions

1.	You have your laptop directly connected into a router's Ethernet port. Which of the following are among the requirements for the command to be successful?
A.	1, 3 and 4
B.	2, 4 and 5
C.	3 and 5 only
D.	5 only
Answer» C. 3 and 5 only

Discussion

2.	What information is displayed by the command?
A.	1, 2 and 3
B.	1 and 4
C.	3, 4, and 5
D.	All of the above
Answer» C. 3, 4, and 5

Discussion

3.	What does the command provide?
A.	It is used to restart the router.
B.	It is used to bypass the configuration in NVRAM.
C.	It is used to enter ROM Monitor mode.
D.	It is used to view the lost password.
Answer» C. It is used to enter ROM Monitor mode.

Discussion

4.	Which three commands can be used to check LAN connectivity problems on a router?1. show interfaces2. show ip route3. tracert4. ping5. dns lookups
A.	,2 and 4
B.	and 5
C.	and 5
D.	one of the above
Answer» B. and 5

Discussion

5.	You are unsuccessful in telnetting into a remote device. What could the problem be?1. IP addresses are incorrect.2. Access control list is filtering Telnet.3. There is a defective serial cable.4. The VTY password is missing.
A.	only
B.	only
C.	and 4 only
D.	ll of the above
Answer» D. ll of the above

Discussion

6.	What information is displayed by the show hosts command?1. Temporary DNS entries2. The names of the routers created using the hostname command3. The IP addresses of workstations allowed to access the router4. Permanent name-to-address mappings created using the ip host command5. The length of time a host has been connected to the router via Telnet
A.	, 2 and 3
B.	and 4
C.	, 4, and 5
D.	ll of the above
Answer» C. , 4, and 5

Discussion

7.	You are troubleshooting a connectivity problem in your corporate network and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. What IOS user exec command should you issue?
A.	Router> ping
B.	Router> trace
C.	Router> show ip route
D.	Router> show interface
Answer» C. Router> show ip route

Discussion

8.	You need to gather the IP address of a remote switch that is located in Hawaii. What can you do to find the address?
A.	Issue the show ip arp command on the router connected to the switch.
B.	Issue the show ip route command on the router connected to the switch.
C.	Issue the show cdp neighbor command on the router connected to the switch.
D.	Issue the show cdp neighbors detail command on the router connected to the switch.
Answer» E.

Discussion

9.	Which command loads a new version of the Cisco IOS into a router?
A.	copy flash ftp
B.	copy ftp flash
C.	copy flash tftp
D.	copy tftp flash
Answer» E.

Discussion

10.	The configuration register setting of 0x2102 provides what function to a router?
A.	Tells the router to boot into ROM monitor mode
B.	Provides password recovery
C.	Tells the router to look in NVRAM for the boot sequence
D.	Boots the IOS from a TFTP server
Answer» D. Boots the IOS from a TFTP server

Discussion

11.	What should the configuration register value be after you successfully complete the password recovery procedure and return the router to normal operation?
A.	0x2100
B.	0x2101
C.	0x2102
D.	0x2142
Answer» D. 0x2142

Discussion

12.	What does the command o/r 0x2142 provide?
A.	It is used to restart the router.
B.	It is used to bypass the configuration in NVRAM.
C.	It is used to enter ROM Monitor mode.
D.	It is used to view the lost password.
Answer» C. It is used to enter ROM Monitor mode.

Discussion

13.	You telnet into a remote device and type debug ip rip, but no output from the debug command is seen. What could the problem be?
A.	You must type the show ip rip command first.
B.	IP addressing on the network is incorrect.
C.	You must use the terminal monitor command.
D.	Debug output is sent only to the console.
Answer» D. Debug output is sent only to the console.

Discussion

14.	A network administrator wants to upgrade the IOS of a router without removing the image currently installed. What command will display the amount of memory consumed by the current IOS image and indicate whether there is enough room available to hold both the current and new images?
A.	show version
B.	show flash
C.	show memory
D.	show buffers
Answer» C. show memory

Discussion

15.	You telnet to a router and make your necessary changes; now you want to end the Telnet session. What command do you type in?
A.	close
B.	disable
C.	disconnect
D.	exit
Answer» E.

Discussion

16.	You copy a configuration from a network host to a router's RAM. The configuration looks correct, yet it is not working at all. What could the problem be?
A.	You copied the wrong configuration into RAM.
B.	You copied the configuration into flash memory instead.
C.	The copy did not override the shutdown command in running-config.
D.	The IOS became corrupted after the copy command was initiated.
Answer» D. The IOS became corrupted after the copy command was initiated.

Discussion

17.	Which command will show you the IOS version running on your router?
A.	sh IOS
B.	sh flash
C.	sh version
D.	sh running-config
Answer» D. sh running-config

Discussion

18.	You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?
A.	You didn't boot the router with the correct command.
B.	NVRAM is corrupted.
C.	The configuration register setting is incorrect.
D.	The newly upgraded IOS is not compatible with the hardware of the router.
Answer» D. The newly upgraded IOS is not compatible with the hardware of the router.

Discussion

19.	Which three commands can be used to check LAN connectivity problems on a router? show interfaces show ip route tracert ping dns lookups
A.	1 ,2 and 4
B.	2 and 5
C.	3 and 5
D.	None of the above
Answer» B. 2 and 5

Discussion

20.	Which command displays the configuration register setting?
A.	show ip route
B.	show boot version
C.	show version
D.	show flash
Answer» D. show flash

Discussion

21.	What information is displayed by the show hosts command? Temporary DNS entries The names of the routers created using the hostname command The IP addresses of workstations allowed to access the router Permanent name-to-address mappings created using the ip host command The length of time a host has been connected to the router via Telnet
A.	1, 2 and 3
B.	1 and 4
C.	3, 4, and 5
D.	All of the above
Answer» C. 3, 4, and 5

Discussion

22.	Which command will copy the IOS to a backup host on your network?
A.	transfer IOS to 172.16.10.1
B.	copy run start
C.	copy start tftp
D.	copy flash tftp
Answer» E.

Discussion

23.	You are unsuccessful in telnetting into a remote device. What could the problem be? IP addresses are incorrect. Access control list is filtering Telnet. There is a defective serial cable. The VTY password is missing.
A.	1 only
B.	3 only
C.	2 and 4 only
D.	All of the above
Answer» D. All of the above

Discussion

24.	If you want to have more than one Telnet session open at the same time, what keystroke combination would you use?
A.	Tab+Spacebar
B.	Ctrl+X, then 6
C.	Ctrl+Shift+X, then 6
D.	Ctrl+Shift+6, then X
Answer» E.

Discussion

25.	The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?
A.	RAM should be erased and the router restarted.
B.	Flash should be erased and the router restarted.
C.	NVRAM should be erased and the router restarted.
D.	The new configuration should be entered and saved.
Answer» D. The new configuration should be entered and saved.

Discussion

26.	You have your laptop directly connected into a router's Ethernet port. Which of the following are among the requirements for the copy flash tftp command to be successful? TFTP server software must be running on the router. TFTP server software must be running on your laptop. The Ethernet cable connecting the laptop directly into the router's Ethernet port must be a straight-through cable. The laptop must be on the same subnet as the router's Ethernet interface. The copy flash tftp command must be supplied the IP address of the laptop.
A.	1, 3 and 4
B.	2, 4 and 5
C.	3 and 5 only
D.	5 only
Answer» C. 3 and 5 only

Discussion

Explore topic-wise MCQs in Networking.

You have your laptop directly connected into a router's Ethernet port. Which of the following are among the requirements for the command to be successful?

What information is displayed by the command?

What does the command provide?

Which three commands can be used to check LAN connectivity problems on a router?1. show interfaces2. show ip route3. tracert4. ping5. dns lookups

You are unsuccessful in telnetting into a remote device. What could the problem be?1. IP addresses are incorrect.2. Access control list is filtering Telnet.3. There is a defective serial cable.4. The VTY password is missing.

You are troubleshooting a connectivity problem in your corporate network and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. What IOS user exec command should you issue?

You need to gather the IP address of a remote switch that is located in Hawaii. What can you do to find the address?

Which command loads a new version of the Cisco IOS into a router?

The configuration register setting of 0x2102 provides what function to a router?

What should the configuration register value be after you successfully complete the password recovery procedure and return the router to normal operation?

What does the command o/r 0x2142 provide?

You telnet into a remote device and type debug ip rip, but no output from the debug command is seen. What could the problem be?

A network administrator wants to upgrade the IOS of a router without removing the image currently installed. What command will display the amount of memory consumed by the current IOS image and indicate whether there is enough room available to hold both the current and new images?

You telnet to a router and make your necessary changes; now you want to end the Telnet session. What command do you type in?

You copy a configuration from a network host to a router's RAM. The configuration looks correct, yet it is not working at all. What could the problem be?

Which command will show you the IOS version running on your router?

You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?

Which three commands can be used to check LAN connectivity problems on a router? show interfaces show ip route tracert ping dns lookups

Which command displays the configuration register setting?

Which command will copy the IOS to a backup host on your network?

You are unsuccessful in telnetting into a remote device. What could the problem be? IP addresses are incorrect. Access control list is filtering Telnet. There is a defective serial cable. The VTY password is missing.

If you want to have more than one Telnet session open at the same time, what keystroke combination would you use?

The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?