Explore topic-wise MCQs in Electronic Mechanic.

This section includes 42 Mcqs, each offering curated multiple-choice questions to sharpen your Electronic Mechanic knowledge and support exam preparation. Choose a topic below to get started.

1.

Capacitive reactance is inversely proportional to ________.

A. Voltage
B. Capacitance
C. Frequency
D. Both capacitance and frequency
Answer» E.
2.

Calculate the current in I3 in the circuit.

A. -8 A
B. 8 A
C. 7 A
D. 12 A
Answer» C. 7 A
3.

A transformer has a primary to secondary turns ratio of 1:2. 50 V rms, 50 Hz sine wave is applied at primary winding. The peak secondary voltage will be

A. 100 V
B. 25 V
C. 141.4 V
D. 35.35 V
Answer» D. 35.35 V
4.

A capacitor dissipates _________ energy.

A. No
B. 10% of the stored
C. 20% of the stored
D. 50% of the stored
Answer» B. 10% of the stored
5.

If 100 coulomb of charge passes through a conductor in 25 s, the current in the conductor is _____

A. 1 A
B. 4 A
C. 10 A
D. 2.5 A
Answer» C. 10 A
6.

Identify the anode material in a Leclanche cell from the given options

A. Ammonia
B. Zinc
C. Carbon
D. Magnesium
Answer» C. Carbon
7.

Conductivity of semiconductor _____ with temperature

A. Increases
B. Decreases
C. Does not change
D. Varies randomly
Answer» B. Decreases
8.

A fuse should be connected in

A. Series of neutral conductor
B. Parallel of neutral conductor
C. Series of live conductor
D. Parallel of live conductor
Answer» D. Parallel of live conductor
9.

On what principle do fuses work?

A. Heating effect of resistance
B. Heating effect of voltage
C. Heating effect of electrodes
D. Heating effect of current
Answer» E.
10.

In actual practice, the rating of transformer is specified in:

A. kW
B. kVA
C. kVAR
D. kA
Answer» C. kVAR
11.

In a 3-phase system, there phase voltages are displaced by an angle of….

A. 90°
B. 120°
C. 180°
D. 270°
Answer» C. 180°
12.

Directions: It consists of two statements one labeled as statement I and the other as statement II. Examine these two statements carefully and select the correct answer using the code given below.Statement I: If a squirrel cage motor is started at full rated voltage, the power supply could be damaged.Statement II: For squirrel cage induction motors, starting current is high and power factor at starting is low.

A. Both statements I and statement II are individually true and statement II is the correct explanation of statement I
B. Both statement I and statement II are individually true but statement II is not the correct explanation of statement I
C. Statements I is true but statement II is false
D. Statement I is false but statement II is true
Answer» E.
13.

If 1 micro ampere current is flowing through a conductor, then the number of electrons flowing through in one second are

A. 6.28 × 1022
B. 6.28 × 1015
C. 6.28 × 1019
D. 6.28 × 1012
Answer» E.
14.

If 12 V are applied to a circuit that consumes 78 Watt, what is the current flow through circuit

A. 6.5 A
B. 0.65 A
C. 65 mA
D. 12 A
Answer» B. 0.65 A
15.

Maximum power is transferred when

A. Load Impedance > Source Impedance
B. Load Impedance < Source Impedance
C. Load Impedance = Source Impedance
D. Load Impedance = 0
Answer» D. Load Impedance = 0
16.

Cables that transmits signals in form of light is

A. Unwired
B. Fiber optic cable
C. Coaxial cable
D. Twisted pair cable
Answer» C. Coaxial cable
17.

In AC circuits, laminated iron is invariably used in order to

A. Reduce eddy current loss
B. Increase heat radiation
C. Make assembly cheap and easier
D. Reduce circuit permeability
Answer» B. Increase heat radiation
18.

A resistor used in color TV has the following color bands (in this order): yellow, violet, orange and silver. Its nominal value is

A. 4.7 kΩ ± 10%
B. 4.7 kΩ ± 5%
C. 47 kΩ ± 10%
D. 470 kΩ ± 5%
Answer» D. 470 kΩ ± 5%
19.

Hysteresis loss in a transformer is caused by

A. Induced voltage in the core due to changing magnetic field
B. Variation in input frequency
C. Energy consumed in reversing the magnetism of iron core
D. Fluctuation in load current
Answer» D. Fluctuation in load current
20.

Identify the port shown in the image below.

A. HDMI
B. DVI
C. MIDI
D. FireWire
Answer» B. DVI
21.

Name the connector shown in the picture.

A. XLR connector female
B. BNC connector
C. TRS plus female
D. RCA plug
Answer» B. BNC connector
22.

In which one of the following is flexible wire is not used?

A. T.V
B. Table fan
C. Table light
D. Cement factory
Answer» E.
23.

If the capacity of a battery is 4000mAh, it can supply 4 Ampere current for

A. 120 min
B. 240 min
C. 60 min
D. 30 min
Answer» D. 30 min
24.

An air capacitor has its plates separated by a 0.1 cm distance. The total area of the plates is 10 cm2. Identify the value of capacitor from the options given below.

A. 8.85 pF
B. 10 pF
C. 88.5 pF
D. 100 pF
Answer» B. 10 pF
25.

HRC is a type of:

A. Fuse
B. Switch
C. Circuit breaker
D. Connector
Answer» B. Switch
26.

Five cells, each with an e.m.f. of 2V and internal resistance of 0.5 Ω are connected in series. The resulting battery will have

A. An e.m.f. of 2V and an internal resistance of 0.5 Ω
B. An e.m.f. of 10V and an internal resistance of 2.5 Ω
C. An e.m.f. of 2V and an internal resistance of 0.1 Ω
D. An e.m.f. of 10V and an internal resistance of 0.1 Ω
Answer» C. An e.m.f. of 2V and an internal resistance of 0.1 Ω
27.

A conductor of 100 m length with 1 mm diameter has a resistance of 900 mΩ. What will be the resistance of another conductor of same material with same length and 3 mm diameter?

A. 300 mΩ
B. 100 mΩ
C. 2700 mΩ
D. None of the above
Answer» C. 2700 mΩ
28.

If the frequency of a radio wave is increased, then its wave length will

A. Increase
B. Decrease
C. Remains the same
D. Cannot tell
Answer» C. Remains the same
29.

Loading of a cable is done to1. Increase its inductance2. Increase its leakage resistance3. Decrease its leakage resistance4. Achieve distortion less condition

A. 1, 3 & 4
B. 1 & 3 only
C. 2 & 4 only
D. 1 & 4 only
Answer» D. 1 & 4 only
30.

5 resistors of 10 Ω are connected in parallel. A current of 1 A flows through each of them. What will be the current through each of them if they are connected in series?

A. 0.2 A
B. 5 A
C. 0.5 A
D. 1 A
Answer» B. 5 A
31.

A transformer with input 60 W power at the primary has an efficiency of 95%. Identify its power at the secondary from the given options.

A. 45 W
B. 95 W
C. 100 W
D. 57 W
Answer» E.
32.

Find Current, if Resistance = 50 ohms and Power = 100 Watts

A. 2 A
B. 1.414 A
C. 3 A
D. 1.314 A
Answer» C. 3 A
33.

In a particular circuit connection, AWG 18 wire is selected over AWG 22. The reason is that it is having

A. Lesser weight
B. Less thickness
C. Higher resistance
D. Higher current carrying capacity
Answer» E.
34.

Find the voltage across 24 Ω resistor.

A. 8 V
B. 9 V
C. 1 V
D. 6 V
Answer» B. 9 V
35.

Percentage voltage regulation = __________ × 100; (Where VNL = No Load Voltage, VFL = Full Load Voltage)

A. (VNL - VFL) / VFL­
B. (VNL - VFL) / VNL­
C. VFL / VNL
D. VNL / VFL
Answer» B. (VNL - VFL) / VNL­
36.

In a Transformer, if the secondary voltage is greater than primary voltage, then what type of transformer is this?

A. Transformer on DC Supply
B. Step Down Transformer
C. Ideal Transformer
D. Step Up Transformer
Answer» E.
37.

If 120 Coulomb of charge passes through a conductor in 60 sec, the current in the conductor is

A. 0.5 A
B. 2 A
C. 3.33 mA
D. 0.3 mA
Answer» C. 3.33 mA
38.

Following transmission media are given:(a) Twisted pair cables(b) Optical fiber cables(c) Coaxial cables(d) MicrowavesFor high rate data transmission systems, arrange the above in terms of their Losses in ascending orders.The correct sequence is given by:

A. (b), (c), (a), (d)
B. (d), (c), (a), (b)
C. (a), (b), (c), (d)
D. (b), (d), (c), (a)
Answer» E.
39.

If Vp is peak voltage of a sine wave then RMS voltage will be

A. Vp/2
B. \(\frac{{{V_p}}}{{\sqrt 2 }}\)
C. \(\frac{{V_p^2}}{2}\)
D. Vp/4
Answer» C. \(\frac{{V_p^2}}{2}\)
40.

Identify the circuit.

A. High pass filter
B. Bandpass filter
C. Low pass filter
D. Band reject filter
Answer» D. Band reject filter
41.

Find the current through 3-ohm resistor

A. 6 A
B. 2 A
C. 2.67 A
D. 3 A
Answer» C. 2.67 A
42.

Boost charge is given to a

A. Dead battery
B. The battery in danger of becoming over-discharged during a working shift
C. Fully charged battery
D. Completely discharged battery
Answer» E.