MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 20 Mcqs, each offering curated multiple-choice questions to sharpen your Machine Design knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Slenderness ratio is inversely proportional to __________ |
| A. | Effective height |
| B. | Effective thickness |
| C. | Effective length |
| D. | Effective height and effective thickness |
| Answer» C. Effective length | |
| 2. |
The nominal thickness of one brick wall in case of modular bricks is __________ |
| A. | 18 cm |
| B. | 19 cm |
| C. | 20 cm |
| D. | 21 cm |
| Answer» D. 21 cm | |
| 3. |
The actual thickness of one brick wall in case of modular bricks is __________ |
| A. | 18 cm |
| B. | 19 cm |
| C. | 20 cm |
| D. | 21 cm |
| Answer» C. 20 cm | |
| 4. |
Stability problem results when slenderness ratio is more than __________ |
| A. | 30 |
| B. | 40 |
| C. | 50 |
| D. | 60 |
| Answer» B. 40 | |
| 5. |
Slenderness ratio of a wall does not depend on __________ |
| A. | Height of the wall |
| B. | Length of the wall |
| C. | Mass of the wall |
| D. | Thickness of the wall |
| Answer» D. Thickness of the wall | |
| 6. |
Weak mortar has __________ |
| A. | Only lime |
| B. | Only cement |
| C. | More cement and less lime |
| D. | More lime and less cement |
| Answer» E. | |
| 7. |
In a masonry wall, the strength of the mortar should be __________ that of the masonry unit. |
| A. | Lesser than |
| B. | Greater than |
| C. | Equal to |
| D. | Greater than or equal to |
| Answer» B. Greater than | |
| 8. |
Live loads and dead loads act in a horizontal direction. |
| A. | True |
| B. | False |
| Answer» C. | |
| 9. |
Which of the following reasons is not responsible for setting up stresses in a wall? |
| A. | Its own weight |
| B. | Weight of superimposed loads |
| C. | Cement |
| D. | Lateral pressure |
| Answer» D. Lateral pressure | |
| 10. |
Which of the following is not a type of load coming on the wall structures? |
| A. | Dead load |
| B. | Black load |
| C. | Live load |
| D. | Earthquake load |
| Answer» C. Live load | |
| 11. |
IN_MANUAL_ASSEMBLY,_COST_OF_SCREW_IS_HIGHER_THAN_THE_COST_OF_DRIVING_A_SCREW.?$ |
| A. | True |
| B. | False |
| Answer» C. | |
| 12. |
Maximum_carbon_content_in_welding_is_usually_limited_to$ |
| A. | 0.22% |
| B. | 0.8% |
| C. | 1.5% |
| D. | 2% |
| Answer» B. 0.8% | |
| 13. |
Among casting, forging and forging which has the slowest rate of production? |
| A. | Casting |
| B. | Forging |
| C. | Machining |
| D. | All have equal rate of production |
| Answer» D. All have equal rate of production | |
| 14. |
Forged components can be held between close limits. |
| A. | True |
| B. | False |
| Answer» B. False | |
| 15. |
In forging, metal is in which of the following stage? |
| A. | Elastic |
| B. | Plastic |
| C. | Can be in any stage |
| D. | Rigid |
| Answer» C. Can be in any stage | |
| 16. |
Cast surfaces have good finishing. |
| A. | True |
| B. | False |
| Answer» C. | |
| 17. |
While designing a forging, the profile is selected such that the fibrous lines are parallel to the tensile forces and perpendicular to shear forces. |
| A. | True |
| B. | False |
| Answer» B. False | |
| 18. |
Which process allows controlling grain structure of the product? |
| A. | Casting |
| B. | Forging |
| C. | None of the mentioned |
| D. | Die Casting |
| Answer» C. None of the mentioned | |
| 19. |
Shot blasting process improves the endurance limit of the component. |
| A. | True |
| B. | False |
| Answer» B. False | |
| 20. |
Stressed parts are always kept in tension. |
| A. | True |
| B. | False |
| Answer» B. False | |