Explore topic-wise MCQs in Testing Subject.

This section includes 657 Mcqs, each offering curated multiple-choice questions to sharpen your Testing Subject knowledge and support exam preparation. Choose a topic below to get started.

1.

Which tells about low level transmission and framing?

A. v series
B. x series
C. g series
D. q series
Answer» D. q series
2.

Which uses UDP?

A. echo
B. time
C. domain name server
D. all of the mentioned
Answer» E.
3.

Which is connection oriented and which is connection-less?

A. datagrams, virtual circuits
B. virtual circuits, datagrams
C. datagrams
D. none of the mentioned
Answer» C. datagrams
4.

Which uses TCP?

A. simple mail transfer protocol
B. simple network management protocol
C. simple mail transfer & network management protocol
D. none of the mentioned
Answer» B. simple network management protocol
5.

Routing is performed only centrally.

A. true
B. false
Answer» B. false
6.

Routing is

A. static
B. dynamic
C. static & dynamic
D. none of the mentioned
Answer» D. none of the mentioned
7.

Window given the number of

A. bytes
B. frames
C. bytes & frames
D. none of the mentioned
Answer» D. none of the mentioned
8.

The time required to transmit frame depends on

A. frame size
B. channel capacity
C. frame size & channel capacity
D. none of the mentioned
Answer» D. none of the mentioned
9.

In wireless network an extended service set is a set of

A. connected basic service sets
B. all stations
C. all access points
D. connected access points
Answer» B. all stations
10.

Mostly                  is used in wireless LAN.

A. time division multiplexing
B. orthogonal frequency division multiplexing
C. space division multiplexing
D. channel division multiplexing
Answer» C. space division multiplexing
11.

A wireless network interface controller can work in

A. infrastructure mode
B. ad-hoc mode
C. both infrastructure mode and ad-hoc mode
D. wds mode
Answer» D. wds mode
12.

In wireless distribution system

A. multiple access point are inter-connected with each other
B. there is no access point
C. only one access point exists
D. access points are not required
Answer» B. there is no access point
13.

Which multiple access technique is used by IEEE 802.11 standard for wireless LAN?

A. cdma
B. csma/ca
C. aloha
D. csma/cd
Answer» C. aloha
14.

In wireless ad-hoc network

A. access point is not required
B. access point is must
C. nodes are not required
D. all nodes are access points
Answer» B. access point is must
15.

The maximum size of payload field in ethernet frame is

A. 1000 bytes
B. 1200 bytes
C. 1300 bytes
D. 1500 bytes
Answer» E.
16.

High speed ethernet works on

A. coaxial cable
B. twisted pair cable
C. optical fiber
D. unshielded twisted pair cable
Answer» D. unshielded twisted pair cable
17.

An ethernet frame that is less than the IEEE 802.3 minimum length of 64 octets is called

A. short frame
B. runt frame
C. mini frame
D. man frame
Answer» C. mini frame
18.

Ethernet in metropolitan area network (MAN) can be used as

A. pure ethernet
B. ethernet over sdh
C. ethernet over mpls
D. all of the mentioned
Answer» E.
19.

What is autonegotiation?

A. a procedure by which two connected devices choose common transmission parameters
B. a security algorithm
C. a routing algorithm
D. encryption algorithm
Answer» B. a security algorithm
20.

A point-to-point protocol over ethernet is a network protocol for

A. encapsulating ppp frames inside ethernet frames
B. encapsulating ehternet framse inside ppp frames
C. for security of ethernet frames
D. for security of ppp frames
Answer» B. encapsulating ehternet framse inside ppp frames
21.

MAC address is of

A. 24 bits
B. 36 bits
C. 42 bits
D. 48 bits
Answer» E.
22.

CRC uses

A. multiplication
B. binary division
C. multiplication & binary division
D. none of the mentioned
Answer» D. none of the mentioned
23.

Which is more efficient?

A. parity check
B. cyclic redundancy check
C. parity & cyclic redundancy check
D. none of the mentioned
Answer» C. parity & cyclic redundancy check
24.

Which can detect two bit errors?

A. parity check
B. cyclic redundancy check
C. parity & cyclic redundancy check
D. none of the mentioned
Answer» C. parity & cyclic redundancy check
25.

How error detection and correction is done?

A. by passing it through equalizer
B. by passing it through filter
C. by amplifying it
D. by adding redundancy bits
Answer» E.
26.

In synchronous transmission, receiver must stay synchronous for

A. 4 bits
B. 8 bits
C. 9 bits
D. 16 bits
Answer» D. 16 bits
27.

Which has continuous transmission?

A. asynchronous
B. synchronous
C. asynchronous & synchronous
D. none of the mentioned
Answer» C. asynchronous & synchronous
28.

Which has comparatively high frequency component?

A. sine wave
B. cosine wave
C. square wave
D. none of the mentioned
Answer» D. none of the mentioned
29.

Which requires bit transitions?

A. asynchronous
B. synchronous
C. asynchronous & synchronous
D. none of the mentioned
Answer» C. asynchronous & synchronous
30.

Which can be used as an intermediate device in between transmitter entity and receiver entity?

A. ip router
B. microwave router
C. telephone switch
D. all of the mentioned
Answer» E.
31.

In layering, n layers provide service to

A. n layer
B. n-1 layer
C. n+1 layer
D. none of the mentioned
Answer» D. none of the mentioned
32.

The technique of temporarily delaying outgoing acknowledgements so that they can be hooked onto the next outgoing data frame is called

A. piggybacking
B. cyclic redundancy check
C. fletcher’s checksum
D. parity check
Answer» B. cyclic redundancy check
33.

Automatic repeat request error management mechanism is provided by

A. logical link control sublayer
B. media access control sublayer
C. network interface control sublayer
D. application access control sublayer
Answer» B. media access control sublayer
34.

Which of the following is the multiple access protocol for channel access control?

A. csma/cd
B. csma/ca
C. both csma/cd & csma/ca
D. hdlc
Answer» D. hdlc
35.

When 2 or more bits in a data unit has been changed during the transmission, the error is called

A. random error
B. burst error
C. inverted error
D. double error
Answer» C. inverted error
36.

Header of a frame generally contains

A. synchronization bytes
B. addresses
C. frame identifier
D. all of the mentioned
Answer» E.
37.

Which sublayer of the data link layer performs data link functions that depend upon the type of medium?

A. logical link control sublayer
B. media access control sublayer
C. network interface control sublayer
D. error control sublayer
Answer» C. network interface control sublayer
38.

Which are non negative functions?

A. pdf
B. pmf
C. pdf & pmf
D. none of the mentioned
Answer» D. none of the mentioned
39.

Cumulative distributive function is

A. non negative
B. non decreasing
C. non negative & decreasing
D. none of the mentioned
Answer» D. none of the mentioned
40.

Constellation diagram is plotted in

A. constellation space
B. signal space
C. orthogonal space
D. boundary space
Answer» C. orthogonal space
41.

A band-pass signal has

A. dc component
B. no dc component
C. no side lobes
D. cannot be determined
Answer» C. no side lobes
42.

Which are orthonormal signal representation?

A. sine and cosine at same frequency
B. wavelets
C. complex sinusoids at a different frequency
D. all of the mentioned
Answer» E.
43.

A band-pass signal has a Fourier transform equal to

A. one
B. zero
C. infinity
D. cannot be determined
Answer» C. infinity
44.

Which can be used for periodic and non periodic?

A. fourier series
B. fourier transforms
C. fourier series & transforms
D. none of the mentioned
Answer» C. fourier series & transforms
45.

Random things in a communication system are

A. timing offset
B. device frequency
C. attenuation
D. all of the mentioned
Answer» E.
46.

Fourier transform of a signal gives the

A. frequency content
B. bandwidth
C. frequency content & bandwidth
D. none of the mentioned
Answer» D. none of the mentioned
47.

A band-pass signal can be down-converted using

A. sine wave
B. cosine wave
C. time delayed wave
D. none of the mentioned
Answer» C. time delayed wave
48.

In down-conversion multiplication with cosine wave is followed by

A. low pass filter
B. high pass filter
C. bandpass filter
D. bandstop filter
Answer» B. high pass filter
49.

A base-band signal can be up-converted using

A. sine wave
B. cosine wave
C. filtering
D. none of the mentioned
Answer» C. filtering
50.

Properties of Fourier transform are

A. duality property
B. time shifting property
C. modulation property
D. all of the mentioned
Answer» E.