MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 11 Mcqs, each offering curated multiple-choice questions to sharpen your Engineering Metrology knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Which of the following option is true for given statements about automatic inspection machines?Statement 1: Safety devices are incorporated to avoid damage to the gauging fixture.Statement 2: Gauging devices entering the part is positively pushed. |
| A. | T, T |
| B. | T, F |
| C. | F, T |
| D. | F, F |
| Answer» C. F, T | |
| 2. |
Which of the following statement is true for automatic inspection machines?Statement 1: Measurement information is displayed on the screen.Statement 2: Bad parts are not segregated automatically. |
| A. | T, F |
| B. | F, F |
| C. | F, T |
| D. | T, T |
| Answer» B. F, F | |
| 3. |
WHICH_OF_THE_FOLLOWING_OPTION_IS_TRUE_FOR_GIVEN_STATEMENTS_ABOUT_AUTOMATIC_INSPECTION_MACHINES??$ |
| A. | |
| B. | |
| Answer» C. | |
| 4. |
Which of the following is true about the design of structure of automatic inspection machine? |
| A. | Separate structure is designed for transportation and gauging system |
| B. | Same structure is designed for transportation and gauging system |
| C. | Anti vibration mounts are placed only one leg of gauging structure |
| D. | Anti vibration mounts are placed only on two front legs of gauging structure |
| Answer» B. Same structure is designed for transportation and gauging system | |
| 5. |
Why retooling is fast and less expensive in automatic inspection machines? |
| A. | Only hardware changes are needed |
| B. | Both hardware and software changes are needed |
| C. | No hardware changes are needed |
| D. | Software program doesn’t need any change |
| Answer» D. Software program doesn‚Äö√Ñ√∂‚àö√ë‚àö¬•t need any change | |
| 6. |
Which of the following statement is true for automatic inspection machines? |
| A. | |
| B. | |
| Answer» B. | |
| 7. |
Which of the following is true about probes used in automatic inspection machines? |
| A. | Retractable type |
| B. | Non-retractable type |
| C. | Auxiliary probe is not used |
| D. | Heads of probes are not held back till the part is in gauging position |
| Answer» B. Non-retractable type | |
| 8. |
What is done to avoid out-of-sequence mishaps in automatic inspection machine? |
| A. | Clamping between centres and sequence of part lifting are linked on different controls |
| B. | Clamping between centres and gauge fixtures are linked on different controls |
| C. | Sequence of part lifting and gauge fixtures are linked on different controls |
| D. | Sequence of part lifting, clamping between centres and gauge fixtures are linked on same controls |
| Answer» E. | |
| 9. |
Which of the following is true about the self-diagnostic system present in automatic inspection machines? |
| A. | Increase downtime |
| B. | Easy but slow identification |
| C. | Improved efficiency of maintenance |
| D. | Increase settling time |
| Answer» D. Increase settling time | |
| 10. |
What is not a use of rocker-arm components in automatic gauging system? |
| A. | Amplify motion |
| B. | Enable probe to reach very difficult areas |
| C. | Enable positioning of part |
| D. | Transfer movement from datum through not more than one pivot points |
| Answer» E. | |
| 11. |
Which of the following is not true about automatic inspection machine? |
| A. | Human intervention is required to judge the quality |
| B. | Consists a logic system |
| C. | Self diagnostic system is present |
| D. | Microprocessors are present |
| Answer» B. Consists a logic system | |