If you wanted to deny FTP access from network 200.200.10.0 to network 200.199.11.0 but allow everything else, which of the following command strings is valid?

access-list 110 deny 200.200.10.0 to network 200.199.11.0 eq ftp access-list 111 permit ip any 0.0.0.0 255.255.255.255

access-list 1 deny ftp 200.200.10.0 200.199.11.0 any any

access-list 100 deny tcp 200.200.10.0 0.0.0.255 200.199.11.0 0.0.0.255 eq ftp

access-list 198 deny tcp 200.200.10.0 0.0.0.255 200.199.11.0 0.0.0.255 eq ftp access-list 198 permit ip any 0.0.0.0 255.255.255.255

If you wanted to deny FTP access from network 200.200.10.0 to network

1.	If you wanted to deny FTP access from network 200.200.10.0 to network 200.199.11.0 but allow everything else, which of the following command strings is valid?
A.	<i class="networking-code">access-list 110 deny 200.200.10.0 to network 200.199.11.0 eq ftp<br> access-list 111 permit ip any 0.0.0.0 255.255.255.255</i>
B.	<i class="networking-code">access-list 1 deny ftp 200.200.10.0 200.199.11.0 any any</i>
C.	<i class="networking-code">access-list 100 deny tcp 200.200.10.0 0.0.0.255 200.199.11.0 0.0.0.255 eq ftp</i>
D.	<i class="networking-code">access-list 198 deny tcp 200.200.10.0 0.0.0.255 200.199.11.0 0.0.0.255 eq ftp<br> access-list 198 permit ip any 0.0.0.0 255.255.255.255</i>
Answer» E.

Discussion

No Comment Found

Related MCQs

What VTP mode allows you to change VLAN information on the switch?
You want to improve network performance by increasing the bandwidth available to hosts and limit the size of the broadcast domains. Which of the following options will achieve this goal?
Which of the following provide inter-switch VLAN communication? <ol class="networking-ol-123"><li> ISL </li><li> VTP </li><li> 802.1Q </li><li> 802.3Z </li></ol>
Which of the following protocols are used to configure trunking on a switch? <ol class="networking-ol-123"><li> VLAN Trunk Protocol </li><li> VLAN </li><li> 802.1Q </li><li> ISL </li></ol>
To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met? <ol class="networking-ol-123"><li> Each end of the trunk link must be set to the IEEE 802.1e encapsulation. </li><li> The VTP management domain name of both switches must be set the same. </li><li> All ports on both the switches must be set as access ports. </li><li> One of the two switches must be configured as a VTP server. </li><li> A rollover cable is required to connect the two switches together. </li><li> A router must be used to forward VTP traffic between VLANs. </li></ol>
Which command will show you all the translations active on your router?
Which command would you place on interface connected to the Internet?
Which command would you place on interface on a private network?
Port Address Translation is also termed what?
When creating a pool of global addresses, which of the following can be used instead of the netmask command?

If you wanted to deny FTP access from network 200.200.10.0 to network 200.199.11.0 but allow everything else, which of the following command strings is valid?

Discussion

No Comment Found

Related MCQs

Reply to Comment