In_a_Davis_steering_gear,_the_distance_between_the_pivots_of_the_front_axle_is_1.2_metres_and_the_wheel_base_is_2.7_metres._Find_the_inclination_of_the_track_arm_to_the_longitudinal_axis_of_the_car,_when_it_is_moving_along_a_straight_path.$

In_a_Davis_steering_gear,_the_distance_between_the_pivots_of_the_front

1.	In_a_Davis_steering_gear,_the_distance_between_the_pivots_of_the_front_axle_is_1.2_metres_and_the_wheel_base_is_2.7_metres._Find_the_inclination_of_the_track_arm_to_the_longitudinal_axis_of_the_car,_when_it_is_moving_along_a_straight_path.$
A.	12.5¬¨¬®‚Äö√†√ª
B.	13.5¬¨¬®‚Äö√†√ª
C.	14.5¬¨¬®‚Äö√†√ª
D.	15.5¬¨¬®‚Äö√†√ª
Answer» B. 13.5¬¨¬®‚Äö√†√ª

Discussion

No Comment Found

Related MCQs

In a Davis steering gear, the distance between the pivots of the front axle is 1.2 metres and the wheel base is 2.7 metres. Find the inclination of the track arm to the longitudinal axis of the car, when it is moving along a straight path.
The driving and driven shafts connected by a Hooke’s joint will have equal speeds, if
The Ackerman steering gear mechanism is preferred to the Davis steering gear mechanism, becausea) whole of the mechanism in the Ackerman steering gear is on the back of the front wheelsb) the Ackerman steering gear consists of turning pairsc) the Ackerman steering gear is most economicald) both (
Which of the following mechanism is made up of turning pairs ?a) Scott Russel’s mechanismb) Peaucellier’s mechanismc) Hart’s mechanismd) Both (
A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the minimum speed of the driven shaft if the driving shaft has a constant speed of 500 r.p.m.
A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the maximum speed of the driven shaft if the driving shaft has a constant speed of 500 r.p.m.
A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the minimum speed of the intermediate shaft if the driving shaft has a constant speed of 500 r.p.m.
A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the maximum speed of the intermediate shaft if the driving shaft has a constant speed of 500 r.p.m.
THE_DRIVING_AND_DRIVEN_SHAFTS_CONNECTED_BY_A_HOOKE‚ÄÖ√Ñ√∂‚ÀÖ√Ë‚ÀÖ¬•S_JOINT_WILL_HAVE_EQUAL_SPEEDS,_IF?$#
In_a_Davis_steering_gear,_the_distance_between_the_pivots_of_the_front_axle_is_1.2_metres_and_the_wheel_base_is_2.7_metres._Find_the_inclination_of_the_track_arm_to_the_longitudinal_axis_of_the_car,_when_it_is_moving_along_a_straight_path.$

In_a_Davis_steering_gear,_the_distance_between_the_pivots_of_the_front_axle_is_1.2_metres_and_the_wheel_base_is_2.7_metres._Find_the_inclination_of_the_track_arm_to_the_longitudinal_axis_of_the_car,_when_it_is_moving_along_a_straight_path.$

Discussion

No Comment Found

Related MCQs

Reply to Comment