For the amplifier shown determine the value of the bias current (Ib) and input offset current (Io) respectively.

Ib = IB1 + IB2Io = | IB1 – IB2 |

Ib = 0.5(IB1 + IB2) Io = | IB1 – IB2 |

Ib = 0.5(IB1 + IB2) Io = IB1 – IB2

For the amplifier shown determine the value of the bias current (Ib) a

1.	For the amplifier shown determine the value of the bias current (Ib) and input offset current (Io) respectively.
A.	Ib = IB1 + IB2Io = IB1 – IB2
B.	Ib = IB1 + IB2Io = \| IB1 – IB2 \|
C.	Ib = 0.5(IB1 + IB2) Io = \| IB1 – IB2 \|
D.	Ib = 0.5(IB1 + IB2) Io = IB1 – IB2
Answer» D.

Discussion

No Comment Found

Related MCQs

Consider a Miller integrator with a time constant of 1ms and an input resistance of 10 kΩ. Let the op amp have VOS (offset voltage) = 2 mV and output saturation voltages of ±12 V. What is the corner frequency of the resulting STC network?
Consider a Miller integrator with a time constant of 1ms and an input resistance of 10 kΩ. Let the op amp have VOS (offset voltage) = 2 mV and output saturation voltages of ±12 V. Select the largest possible value for a feedback resistor RF so that at least ±10 V of output signal swing remains available.
Consider a Miller integrator with a time constant of 1ms and an input resistance of 10 kΩ. Let the op amp have VOS (offset voltage) = 2 mV and output saturation voltages of ±12 V. Assuming that when the power supply is turned on the capacitor voltage is zero, how long does it take for the amplifier to saturate?
Consider an inverting amplifier circuit designed using an op amp and two resistors, R1 = 10 kΩ and R2 = 1 MΩ. If the op amp is specified to have an input bias current of 100 nA and an input offset current of 10 nA, find the output dc offset voltage resulting.
Consider the circuit shown below which reduces the impact of the input bias current. If IB1 = IB2 = Input bias current, then determine the value of R3 so that the output voltage (v0) is not impacted by the input bias current.
For the amplifier shown determine the value of the bias current (Ib) and input offset current (Io) respectively.
Consider an inverting amplifier with a nominal gain of 1000 constructed from an op amp with an input offset voltage of 3 mV and with output saturation levels of ±10 V. If the effect of VOs(input offset voltage) is nulled at room temperature (250C). The circuit is to operate at a temperature in the range 0°C to 75°C and the temperature coefficient of VOS is 10 μV/°C?
Consider an inverting amplifier with a nominal gain of 1000 constructed from an op amp with an input offset voltage of 3 mV and with output saturation levels of ±10 V. If the effect of VOs(input offset voltage) is nulled at room temperature (250C), how large an input can one now apply if the circuit is to operate at a constant temperature?
Consider an inverting amplifier with a nominal gain of 1000 constructed from an op amp with an input offset voltage of 3 mV and with output saturation levels of ±10 V. What is (approximately) the peak sine-wave input signal that can be applied without output clipping?

For the amplifier shown determine the value of the bias current (Ib) and input offset current (Io) respectively.

Discussion

No Comment Found

Related MCQs

Reply to Comment