A_FLAT_PLATE_1_M_BY_1_M_IS_PLACED_IN_A_WIND_TUNNEL._THE_VELOCITY_AND_TEMPERATURE_OF_FREE_STREAM_AIR_ARE_80_M/S_AND_10_DEGREE_CELSIUS._THE_FLOW_OVER_THE_WHOLE_LENGTH_OF_THE_PLATE_IS_MADE_TURBULENT_BY_TURBULIZING_GRID_PLACED_UPSTREAM_OF_THE_PLATE._FIND_THE_THICKNESS_OF_THE_HYDRODYNAMIC_BOUNDARY_LAYER_AT_TRAILING_EDGE_OF_THE_PLATE?$

A_FLAT_PLATE_1_M_BY_1_M_IS_PLACED_IN_A_WIND_TUNNEL._THE_VELOCITY_AND_T

1.	A_FLAT_PLATE_1_M_BY_1_M_IS_PLACED_IN_A_WIND_TUNNEL._THE_VELOCITY_AND_TEMPERATURE_OF_FREE_STREAM_AIR_ARE_80_M/S_AND_10_DEGREE_CELSIUS._THE_FLOW_OVER_THE_WHOLE_LENGTH_OF_THE_PLATE_IS_MADE_TURBULENT_BY_TURBULIZING_GRID_PLACED_UPSTREAM_OF_THE_PLATE._FIND_THE_THICKNESS_OF_THE_HYDRODYNAMIC_BOUNDARY_LAYER_AT_TRAILING_EDGE_OF_THE_PLATE?$
A.	19.55 mm
B.	18.55 mm
C.	17.55 mm
D.	16.55 mm
Answer» E.

Discussion

No Comment Found

Related MCQs

A flat plate 1 m by 1 m is placed in a wind tunnel. The velocity and temperature of free stream air are 80 m/s and 10 degree Celsius. The flow over the whole length of the plate is made turbulent by turbulizing grid placed upstream of the plate. Find the heat flow from the surface of the plate
A flat plate 1 m by 1 m is placed in a wind tunnel. The velocity and temperature of free stream air are 80 m/s and 10 degree Celsius. The flow over the whole length of the plate is made turbulent by turbulizing grid placed upstream of the plate. Find the thickness of the hydrodynamic boundary layer at trailing edge of the plate
With respect to above problem, find the value of Nusselt number
For a particular engine, the underside of the crankcase can be idealized as a flat plate measuring 80 cm by 20 cm. The engine runs at 80 km/hr and the crankcase is cooled by the air flowing past it at the same speed. Find loss of the heat from the crank case surface (t S = 25 degree Celsius). Assume the boundary layer to be turbulent
During test-run, air flows at 215 m/s velocity and 25 degree Celsius temperature past a smooth thin model airfoil which can be idealized as a flat plate. If the chord length of the airfoil is 15 cm, find drag per unit width. The relevant physical properties of air arep = 1.82 kg/m3v = 15.53 * 10 -6 m2/s
The average drag coefficient for turbulent boundary layer flow past a thin plate is given byC f = 0.455/ (log 10 R el) 2.58Where R el is the Reynolds number based on plate length. A plate 50 cm wide and 5 m long is kept parallel to the flow of water with free stream velocity 3 m/s. Calculate the drag force on both sides of the plate. For water, kinematic viscosity = 0.01 stokes
A_FLAT_PLATE_1_M_BY_1_M_IS_PLACED_IN_A_WIND_TUNNEL._THE_VELOCITY_AND_TEMPERATURE_OF_FREE_STREAM_AIR_ARE_80_M/S_AND_10_DEGREE_CELSIUS._THE_FLOW_OVER_THE_WHOLE_LENGTH_OF_THE_PLATE_IS_MADE_TURBULENT_BY_TURBULIZING_GRID_PLACED_UPSTREAM_OF_THE_PLATE._FIND_THE_THICKNESS_OF_THE_HYDRODYNAMIC_BOUNDARY_LAYER_AT_TRAILING_EDGE_OF_THE_PLATE?$
A_flat_plate_1_m_by_1_m_is_placed_in_a_wind_tunnel._The_velocity_and_temperature_of_free_stream_air_are_80_m/s_and_10_degree_Celsius._The_flow_over_the_whole_length_of_the_plate_is_made_turbulent_by_turbulizing_grid_placed_upstream_of_the_plate._Find_the_heat_flow_from_the_surface_of_the_plate$
With respect to above problem, find the value of Nusselt numbe?
For a particular engine, the underside of the crankcase can be idealized as a flat plate measuring 80 cm by 20 cm. The engine runs at 80 km/hr and the crankcase is cooled by the air flowing past it at the same speed. Find loss of the heat from the crank case surface (t S = 25 degree Celsius). Assume the boundary layer to be turbulent

Discussion

No Comment Found

Related MCQs

Reply to Comment