MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 9 Mcqs, each offering curated multiple-choice questions to sharpen your Structural Analysis knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Rotational stiffness at joint O for the shown the figure is _____ |
| A. | \(\frac{11EI}{L} \) |
| B. | \(\frac{13EI}{L} \) |
| C. | \(\frac{7EI}{L} \) |
| D. | \(\frac{8EI}{L} \) |
| Answer» E. | |
| 2. |
Required Moment that is to be applied at end A to produce unit rotation if the far end is horizontal roller support as shown in the figure is _____ |
| A. | \(\frac{EI}{L} \) |
| B. | \(\frac{2EI}{L} \) |
| C. | \(\frac{3EI}{L} \) |
| D. | 0 |
| Answer» E. | |
| 3. |
Required Moment that is to be applied at end A to produce unit rotation if the far end is vertical roller support as shown in the figure is _____ |
| A. | \(\frac{EI}{L} \) |
| B. | \(\frac{2EI}{L} \) |
| C. | \(\frac{3EI}{L} \) |
| D. | \(\frac{4EI}{L} \) |
| Answer» D. \(\frac{4EI}{L} \) | |
| 4. |
Stiffness of the end A if the far end B is free is ____ |
| A. | \(\frac{EI}{L} \) |
| B. | \(\frac{2EI}{L} \) |
| C. | \(\frac{3EI}{L} \) |
| D. | 0 |
| Answer» E. | |
| 5. |
Stiffness of the end A if the far end B is vertical guided roller is ____ |
| A. | \(\frac{EI}{L} \) |
| B. | \(\frac{2EI}{L} \) |
| C. | \(\frac{3EI}{L} \) |
| D. | \(\frac{4EI}{L} \) |
| Answer» B. \(\frac{2EI}{L} \) | |
| 6. |
Required Moment that is to be applied at both ends to produce unit rotation on both the simply supported support is _____ |
| A. | \(\frac{EI}{L} \) |
| B. | \(\frac{2EI}{L} \) |
| C. | \(\frac{3EI}{L} \) |
| D. | \(\frac{4EI}{L} \) |
| Answer» C. \(\frac{3EI}{L} \) | |
| 7. |
Required Moment that is to be applied at end A to produce unit rotation if the far end is hinged is _____ |
| A. | \(\frac{EI}{L} \) |
| B. | \(\frac{2EI}{L} \) |
| C. | \(\frac{3EI}{L} \) |
| D. | \(\frac{4EI}{L} \) |
| Answer» D. \(\frac{4EI}{L} \) | |
| 8. |
Stiffness of the end A if the far end B is fixed is ____ |
| A. | \(\frac{EI}{L} \) |
| B. | \(\frac{2EI}{L} \) |
| C. | \(\frac{3EI}{L} \) |
| D. | \(\frac{4EI}{L} \) |
| Answer» E. | |
| 9. |
When a structural member of the uniform section is subjected to a moment at one end only, then the moment required so as to rotate that end to produce a unit slope, is called _____ |
| A. | Resistance of member |
| B. | Stiffness of member |
| C. | Capacity of member |
| D. | Potential of member |
| Answer» C. Capacity of member | |