30 + Mcqs in Riveted Joints Page 1 McqOptions

1.	The flat ends of a boiler are prevented from bulging out and are strengthened by means of _________
A.	connection of plates at right angles
B.	gusset stays
C.	welding
D.	riveting
Answer» C. welding

Discussion

2.	In butt joint when two straps are used the thickness varies between _______ to ________ (T is the thickness of plate to be connected).
A.	T, 1.125T
B.	0.7T, 0.8T
C.	0.5T, T
D.	.a) T, 1.125Tb) 0.7T, 0.8Tc) 0.5T, Td) T, 1.5T
Answer» C. 0.5T, T

Discussion

3.	In butt joint when one strap is used the thickness varies between _______ to ________ (T is the thickness of plate to be connected).
A.	T, 1.125T
B.	0.7T, 0.8T
C.	0.5T, T
D.	.a) T, 1.125Tb) 0.7T, 0.8Tc) 0.5T, Td) T, 1.5T
Answer» B. 0.7T, 0.8T

Discussion

4.	In zigzag lap joint formation when P is the pitch between the rivets, the distance between the rows of rivets should not be less than _____
A.	0.6P
B.	0.8P
C.	P
D.	1.2P
Answer» B. 0.8P

Discussion

5.	Width (L) of overlap of sheets is equal to ________ when d is the diameter of a rivet in case of single-riveted lap joint.
A.	2d
B.	3d
C.	4d
D.	5d
Answer» C. 4d

Discussion

6.	What type of failure will occur when rivets are smaller than necessary?
A.	Tearing of plate between the holes
B.	Tearing of plate between the edges
C.	Shearing of rivet
D.	Crushing of plate
Answer» D. Crushing of plate

Discussion

7.	Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)
A.	31mm
B.	35mm
C.	36mm
D.	40mm
Answer» B. 35mm

Discussion

8.	Which of the following isn’t a main part of rivet?
A.	Head
B.	Shank
C.	Point
D.	Thread
Answer» E.

Discussion

9.	IN_ZIGZAG_LAP_JOINT_FORMATION_WHEN_P_IS_THE_PITCH_BETWEEN_THE_RIVETS,_THE_DISTANCE_BETWEEN_THE_ROWS_OF_RIVETS_SHOULD_NOT_BE_LESS_THAN______?$
A.	0.6P
B.	0.8P
C.	P
D.	1.2P
Answer» B. 0.8P

Discussion

10.	RIVETING_IS_NOT_RECOMMENDED_FOR_ALUMINIUM_ALLOYS.?$
A.	True
B.	False
Answer» C.

Discussion

11.	In butt joint when two straps are used the thickness varies between _______ to ________ (T is the thickness of plate to be connected).$
A.	T, 1.125T
B.	0.7T, 0.8T
C.	0.5T, T
D.	T, 1.5T
Answer» C. 0.5T, T

Discussion

12.	Quality checking of riveted joint is much expensive than that of welded joint.$
A.	True
B.	False
Answer» C.

Discussion

13.	In_butt_joint_when_one_strap_is_used_the_thickness_varies_between_________to__________(T_is_the_thickness_of_plate_to_be_connected).$
A.	T, 1.125T
B.	0.7T, 0.8T
C.	0.5T, T
D.	T, 1.5T
Answer» B. 0.7T, 0.8T

Discussion

14.	In_joining_steel_plate_and_asbestos,_welding_is_preferred_over_riveting.$
A.	True
B.	False
Answer» C.

Discussion

15.	The_flat_ends_of_a_boiler_are_prevented_from_bulging_out_and_are_strengthened_by_means_of__________
A.	connection of plates at right angles
B.	gusset stays
C.	welding
D.	riveting
Answer» C. welding

Discussion

16.	Width (L) of overlap of sheets is equal to ________ when d is the diameter of a rivet in case of single-riveted lap joint?
A.	2d
B.	3d
C.	4d
D.	5d
Answer» C. 4d

Discussion

17.	Among punching and drilling, punching is safer?
A.	True
B.	False
Answer» C.

Discussion

18.	A joint is said to be double-riveted, triple riveted etc. accordingly to the number of sheets used.
A.	True
B.	False
Answer» C.

Discussion

19.	Among punching and drilling, which is cheaper?
A.	Punching
B.	Drilling
C.	Equally expensive
D.	Cannot be determined
Answer» B. Drilling

Discussion

20.	In a lap joint, if the plates are connected to each other when the joint is made with only one row of rivets then it is called double-riveted lap joint.
A.	True
B.	False
Answer» C.

Discussion

21.	Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm¬¨¬®‚Äö√¢¬ß ; Factor of Safety=6)$
A.	31mm
B.	35mm
C.	36mm
D.	40mm
Answer» B. 35mm

Discussion

22.	Tearing of the plate between the edges of the plate and rivet-hole takes place when ____________
A.	they are near to each other
B.	the hole is too near the edge
C.	diameter of rivet is too small
D.	rivet and plate is of different metals
Answer» C. diameter of rivet is too small

Discussion

23.	The amount by which the two rods to be joined are drawn together is called as?
A.	Draw
B.	Portray
C.	Lead
D.	Pitch
Answer» B. Portray

Discussion

24.	Tearing of the plate between the holes is taken when ________________________
A.	they are near to each other
B.	the hole is too near the edge
C.	diameter of rivet is too small
D.	rivet and plate is of different metals
Answer» B. the hole is too near the edge

Discussion

25.	In hot riveting the shank portion is subjected to compressive stress.
A.	True
B.	False
Answer» C.

Discussion

26.	The thickness of the fullering tool is about the ___________ as that of the plates.
A.	double
B.	same
C.	half
D.	one third
Answer» C. half

Discussion

27.	In hand riveting die is a part of hammer.
A.	True
B.	False
Answer» C.

Discussion

28.	The necessary diameter (d) for thickness of plates (t) is ______
A.	d = 6*‚Äö√Ñ√∂‚àö‚Ä†‚àö‚àÇt
B.	d =4*‚Äö√Ñ√∂‚àö‚Ä†‚àö‚àÇt
C.	d =6*‚Äö√Ñ√∂‚àö‚Ä†‚àö‚àÇ2t
D.	d =4*‚Äö√Ñ√∂‚àö‚Ä†‚àö‚àÇ2t
Answer» B. d =4*‚Äö√Ñ√∂‚àö‚Ä†‚àö‚àÇt

Discussion

29.	A rivet is specified as a 20mm rivet. What does it mean?
A.	None of the mentioned
B.	Shank dia 20mm
C.	Head dia 20mm
D.	Both head and shank dia 20mm
Answer» C. Head dia 20mm

Discussion

30.	Which of the following isn‚Äö√Ñ√∂‚àö√ë‚àö¬•t a main part of rivet?
A.	Head
B.	Shank
C.	Point
D.	Thread
Answer» E.

Discussion

Explore topic-wise MCQs in Machine Design.

The flat ends of a boiler are prevented from bulging out and are strengthened by means of _________

In butt joint when two straps are used the thickness varies between _ to __ (T is the thickness of plate to be connected).

In butt joint when one strap is used the thickness varies between _ to __ (T is the thickness of plate to be connected).

In zigzag lap joint formation when P is the pitch between the rivets, the distance between the rows of rivets should not be less than _____

Width (L) of overlap of sheets is equal to ________ when d is the diameter of a rivet in case of single-riveted lap joint.

What type of failure will occur when rivets are smaller than necessary?

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

Which of the following isn’t a main part of rivet?

IN_ZIGZAG_LAP_JOINT_FORMATION_WHEN_P_IS_THE_PITCH_BETWEEN_THE_RIVETS,_THE_DISTANCE_BETWEEN_THE_ROWS_OF_RIVETS_SHOULD_NOT_BE_LESS_THAN______?$

RIVETING_IS_NOT_RECOMMENDED_FOR_ALUMINIUM_ALLOYS.?$

In butt joint when two straps are used the thickness varies between _ to __ (T is the thickness of plate to be connected).$

Quality checking of riveted joint is much expensive than that of welded joint.$

In_butt_joint_when_one_strap_is_used_the_thickness_varies_between_to__(T_is_the_thickness_of_plate_to_be_connected).$

In_joining_steel_plate_and_asbestos,_welding_is_preferred_over_riveting.$

The_flat_ends_of_a_boiler_are_prevented_from_bulging_out_and_are_strengthened_by_means_of__________

Width (L) of overlap of sheets is equal to ________ when d is the diameter of a rivet in case of single-riveted lap joint?

Among punching and drilling, punching is safer?

A joint is said to be double-riveted, triple riveted etc. accordingly to the number of sheets used.

Among punching and drilling, which is cheaper?

In a lap joint, if the plates are connected to each other when the joint is made with only one row of rivets then it is called double-riveted lap joint.

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm¬¨¬®‚Äö√¢¬ß ; Factor of Safety=6)$

Tearing of the plate between the edges of the plate and rivet-hole takes place when ____________

The amount by which the two rods to be joined are drawn together is called as?

Tearing of the plate between the holes is taken when ________________________

In hot riveting the shank portion is subjected to compressive stress.

The thickness of the fullering tool is about the ___________ as that of the plates.

In hand riveting die is a part of hammer.

The necessary diameter (d) for thickness of plates (t) is ______

A rivet is specified as a 20mm rivet. What does it mean?

Which of the following isn‚Äö√Ñ√∂‚àö√ë‚àö¬•t a main part of rivet?

Explore topic-wise MCQs in Machine Design.

The flat ends of a boiler are prevented from bulging out and are strengthened by means of _________

In butt joint when two straps are used the thickness varies between _______ to ________ (T is the thickness of plate to be connected).

In butt joint when one strap is used the thickness varies between _______ to ________ (T is the thickness of plate to be connected).

In zigzag lap joint formation when P is the pitch between the rivets, the distance between the rows of rivets should not be less than _____

Width (L) of overlap of sheets is equal to ________ when d is the diameter of a rivet in case of single-riveted lap joint.

What type of failure will occur when rivets are smaller than necessary?

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

Which of the following isn’t a main part of rivet?

IN_ZIGZAG_LAP_JOINT_FORMATION_WHEN_P_IS_THE_PITCH_BETWEEN_THE_RIVETS,_THE_DISTANCE_BETWEEN_THE_ROWS_OF_RIVETS_SHOULD_NOT_BE_LESS_THAN______?$

RIVETING_IS_NOT_RECOMMENDED_FOR_ALUMINIUM_ALLOYS.?$

In butt joint when two straps are used the thickness varies between _______ to ________ (T is the thickness of plate to be connected).$

Quality checking of riveted joint is much expensive than that of welded joint.$

In_butt_joint_when_one_strap_is_used_the_thickness_varies_between_________to__________(T_is_the_thickness_of_plate_to_be_connected).$

In_joining_steel_plate_and_asbestos,_welding_is_preferred_over_riveting.$

The_flat_ends_of_a_boiler_are_prevented_from_bulging_out_and_are_strengthened_by_means_of__________

Width (L) of overlap of sheets is equal to ________ when d is the diameter of a rivet in case of single-riveted lap joint?

Among punching and drilling, punching is safer?

A joint is said to be double-riveted, triple riveted etc. accordingly to the number of sheets used.

Among punching and drilling, which is cheaper?

In a lap joint, if the plates are connected to each other when the joint is made with only one row of rivets then it is called double-riveted lap joint.

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm¬¨¬®‚Äö√¢¬ß ; Factor of Safety=6)$

Tearing of the plate between the edges of the plate and rivet-hole takes place when ____________

The amount by which the two rods to be joined are drawn together is called as?

Tearing of the plate between the holes is taken when ________________________

In hot riveting the shank portion is subjected to compressive stress.

The thickness of the fullering tool is about the ___________ as that of the plates.

In hand riveting die is a part of hammer.

The necessary diameter (d) for thickness of plates (t) is ______

A rivet is specified as a 20mm rivet. What does it mean?

Which of the following isn‚Äö√Ñ√∂‚àö√ë‚àö¬•t a main part of rivet?

In butt joint when two straps are used the thickness varies between _ to __ (T is the thickness of plate to be connected).

In butt joint when one strap is used the thickness varies between _ to __ (T is the thickness of plate to be connected).

In butt joint when two straps are used the thickness varies between _ to __ (T is the thickness of plate to be connected).$

In_butt_joint_when_one_strap_is_used_the_thickness_varies_between_to__(T_is_the_thickness_of_plate_to_be_connected).$