MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 8 Mcqs, each offering curated multiple-choice questions to sharpen your Design Of Steel Structures knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
For which of the following cases are equal angles preferred in bolted plate girder flange? |
| A. | when large number of connectors are required to connect flange angle to web |
| B. | when very few number of connectors are required to connect flange angle to web |
| C. | for reducing cost |
| D. | for aesthetic appearance |
| Answer» B. when very few number of connectors are required to connect flange angle to web | |
| 2. |
Which of the following angle should be ideally used in bolted plate girder flange? |
| A. | bulb angle |
| B. | equal angle |
| C. | unequal angle with short leg horizontal |
| D. | unequal angle with long leg horizontal |
| Answer» E. | |
| 3. |
The minimum area of flange angles with cover plate for riveted/ bolted plate girder should be |
| A. | 1/6<sup>th</sup> of calculated flange area |
| B. | 1/3<sup>rd</sup> of calculated flange area |
| C. | 1/8<sup>th</sup> of calculated flange area |
| D. | 1/4<sup>th</sup> of calculated flange area |
| Answer» C. 1/8<sup>th</sup> of calculated flange area | |
| 4. |
The optimum depth of web of plate girder is given by |
| A. | (k/f<sub>y</sub>)<sup>0.33</sup> |
| B. | (M<sub>z</sub>k/f<sub>y</sub>) |
| C. | (M<sub>z</sub>k/f<sub>y</sub>)<sup>0.33</sup> |
| D. | (M<sub>z</sub>k/f<sub>y</sub>)<sup>2</sup> |
| Answer» D. (M<sub>z</sub>k/f<sub>y</sub>)<sup>2</sup> | |
| 5. |
When only transverse stiffeners are provided and d/tw < 345 f to meet compression flange buckling criteria, the range of c should be |
| A. | c 4.5d |
| B. | c > 3d |
| C. | c > 1.5d |
| D. | c < 1.5d |
| Answer» E. | |
| 6. |
What is the range of c to meet serviceability criteria when transverse and longitudinal stiffeners are provided at one level only, at 0.2d from compression flange and c/tw 250 w ? |
| A. | c < 0.74d |
| B. | 0.74d c d |
| C. | c d |
| D. | c > 2d |
| Answer» C. c d | |
| 7. |
The depth-to-thickness ratio of web when only transverse stiffeners are provided and c < 0.74d, where c is clear distance between stiffeners and d is depth of web is_____ to meet serviceability criteria |
| A. | 200 <sub>w</sub> |
| B. | 270 <sub>w</sub> |
| C. | > 200 <sub>w</sub> |
| D. | 270 <sub>w</sub> |
| Answer» E. | |
| 8. |
The depth-to-thickness ratio of web when only transverse stiffeners are provided and 3d c d, where c is clear distance between stiffeners and d is depth of web is_____ to meet serviceability criteria |
| A. | 200 <sub>w</sub> |
| B. | 200 <sub>w</sub> |
| C. | > 200 <sub>w</sub> |
| D. | 400 <sub>w</sub> |
| Answer» B. 200 <sub>w</sub> | |