MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 22 Mcqs, each offering curated multiple-choice questions to sharpen your Strength Materials knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
The small projections of plaster are known as ________ |
| A. | Back |
| B. | Dado |
| C. | Dot |
| D. | Hack |
| Answer» D. Hack | |
| 2. |
Which of the following is a defect in plastering? |
| A. | Flaking |
| B. | Scrap |
| C. | Rust |
| D. | Staining |
| Answer» B. Scrap | |
| 3. |
Skimming float is ____________ |
| A. | Wooden float |
| B. | Metalled float |
| C. | Tempered steel float |
| D. | Asbestos cement sheet |
| Answer» B. Metalled float | |
| 4. |
_________ is used to check the level of plastered surface. |
| A. | Gauging trowel |
| B. | Plumb bob |
| C. | Floating Rule |
| D. | Float |
| Answer» D. Float | |
| 5. |
Which of the following is known as” laying trowel”? |
| A. | Float |
| B. | Gauge trowel |
| C. | Floating Rule |
| D. | Skimming float |
| Answer» B. Gauge trowel | |
| 6. |
The thickness of lime plaster varies from _______ to ________ mm. |
| A. | 15 – 20 mm |
| B. | 12 – 15 mm |
| C. | 18 – 25 mm |
| D. | 20 – 25 mm |
| Answer» E. | |
| 7. |
Stucco is a type of _________ |
| A. | Varnishing |
| B. | Distempering |
| C. | Plastering |
| D. | Whitewashing |
| Answer» D. Whitewashing | |
| 8. |
__________IS_USED_TO_CHECK_LEVEL_OF_PLASTERED_SURFACE.?$ |
| A. | Gauging trowel |
| B. | Plumb bob |
| C. | Floating Rule |
| D. | Float |
| Answer» D. Float | |
| 9. |
WHICH_OF_THE_FOLLOWING_IS_KNOWN_AS‚ÄÖ√Ñ√∂‚ÀÖ√Ë‚ÀÖŒÄ_LAYING_TROWEL‚ÄÖ√Ñ√∂‚ÀÖ√Ë‚ÀÖŒÄ??$# |
| A. | Float |
| B. | Gauge trowel |
| C. | Floating Rule |
| D. | Skimming float |
| Answer» B. Gauge trowel | |
| 10. |
Which of the following is a defect in plastering?$ |
| A. | Flaking |
| B. | Scrap |
| C. | Rust |
| D. | Staining |
| Answer» B. Scrap | |
| 11. |
Skimming float is ____________$ |
| A. | Wooden float |
| B. | Metalled float |
| C. | Tempered steel float |
| D. | Asbestos cement sheet |
| Answer» B. Metalled float | |
| 12. |
______ openings or indentations of corrugations in plaster. |
| A. | Helms |
| B. | Grains |
| C. | Keys |
| D. | Flake |
| Answer» D. Flake | |
| 13. |
The small projections of plaster is known as ________ |
| A. | Back |
| B. | Dado |
| C. | Dot |
| D. | Hack |
| Answer» D. Hack | |
| 14. |
________ is a process of mixing various constituents of plaster. |
| A. | Grazing |
| B. | Blistering |
| C. | Gauging |
| D. | Hacking |
| Answer» D. Hacking | |
| 15. |
Which of the following blasters contains pulverized alum? |
| A. | Water proof plaster |
| B. | Plaster on lathe |
| C. | C plaster |
| D. | Marble plaster |
| Answer» B. Plaster on lathe | |
| 16. |
Which of the following plastering is widely adopted in rural areas? |
| A. | Stucco Plastering |
| B. | Mud plastering |
| C. | Lime plastering |
| D. | Asphalt plastering |
| Answer» C. Lime plastering | |
| 17. |
The thickness of lime plaster varies from _______ to ________mm. |
| A. | 15 – 20 mm |
| B. | 12 – 15 mm |
| C. | 18 – 25 mm |
| D. | 20 – 25 mm |
| Answer» E. | |
| 18. |
__________ mm thick plastering is done for stone masonry. |
| A. | 10 mm |
| B. | 15 mm |
| C. | 18 mm |
| D. | 20 mm |
| Answer» E. | |
| 19. |
The thickness of cement plaster should not be more than _______ |
| A. | 15 mm |
| B. | 12 mm |
| C. | 16 mm |
| D. | 20 mm |
| Answer» C. 16 mm | |
| 20. |
Stucco is a type of_________ |
| A. | Varnishing |
| B. | Distempering |
| C. | Plastering |
| D. | Whitewashing |
| Answer» D. Whitewashing | |
| 21. |
Which of the following is not a cross drainage work? |
| A. | Aqueduct |
| B. | Head regulator |
| C. | Super passage |
| D. | Level crossing |
| Answer» C. Super passage | |
| 22. |
Calculate the power transmitted in the shaft at 150 rpm. Take torque as 9000Nm. |
| A. | 140 kW |
| B. | 150 kW |
| C. | 160 kW |
| D. | 175 kW |
| Answer» B. 150 kW | |