MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 10 Mcqs, each offering curated multiple-choice questions to sharpen your Electronic Devices and Circuits knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
How do we calculate Millers capacitance when aV = 250 and C = 9.90pF? |
| A. | 2.485pF |
| B. | 2.485nF |
| C. | 24.85pF |
| D. | 24.85nF |
| Answer» C. 24.85pF | |
| 2. |
Millers compensation and pole splitting is used in the high frequency analysis of BJTs and FETs. |
| A. | True |
| B. | False |
| Answer» B. False | |
| 3. |
What are the applications of Millers compensation and pole splitting? |
| A. | Lower power consumption |
| B. | Additional voltage source |
| C. | Additional current source |
| D. | Circuit optimization |
| Answer» C. Additional current source | |
| 4. |
According to Millers compensation and pole splitting, what is the impedance in output port if I1 = 20 mA, I2 = 30 mA and Z = 2.3 k ? |
| A. | 0.38 k |
| B. | 3.83 k |
| C. | 0.57 k |
| D. | 5.75 k |
| Answer» C. 0.57 k | |
| 5. |
According to Millers compensation and pole splitting, what is the impedance in input port if I1 = 20 mA, I2 = 30 mA and Z = 2.3 k ? |
| A. | 0.38 k |
| B. | 3.83 k |
| C. | 0.57 k |
| D. | 5.75 k |
| Answer» E. | |
| 6. |
What is the impedance from the output port according to Millers compensation and pole splitting? |
| A. | Z<sub>in2</sub> = Z K / K 1 |
| B. | Z<sub>in2</sub> = Z K / K + 1 |
| C. | Z<sub>in2</sub> = Z / K 1 |
| D. | Z<sub>in2</sub> = Z / K + 1 |
| Answer» B. Z<sub>in2</sub> = Z K / K + 1 | |
| 7. |
What is the impedance from the input port according to Millers compensation and pole splitting? |
| A. | Z<sub>in1</sub> = Z K / 1 K |
| B. | Z<sub>in1</sub> = Z K / 1 + K |
| C. | Z<sub>in1</sub> = Z / 1 K |
| D. | Z<sub>in1</sub> = Z / 1 + K |
| Answer» D. Z<sub>in1</sub> = Z / 1 + K | |
| 8. |
According to Millers compensation, what should be the configuration of voltages? |
| A. | Both dependent voltages |
| B. | Both independent voltages |
| C. | One dependent voltage and one independent voltage |
| D. | No specification necessary |
| Answer» D. No specification necessary | |
| 9. |
Which law is the Miller compensation and pole splitting based on? |
| A. | Ohm s Law |
| B. | Moore s Law |
| C. | Coulomb s Law |
| D. | Kirchhoff s Current and Voltage Law |
| Answer» E. | |
| 10. |
What technique is used in Millers compensation? |
| A. | Two port network |
| B. | Hybrid parameters |
| C. | Grounding |
| D. | Short circuiting |
| Answer» B. Hybrid parameters | |