16 + Mcqs in Lithography Page 1 McqOptions

Explore topic-wise MCQs in Pulp Paper.

Dot gain in the mid tones is said to be about __________ lower than with conventional lithography.

must be designed especially for this system to be effective; the principal difference is that the vehicle that’s selected must give suitable rheological properties such as a fairly high viscosity.

The __________ balance in offset lithographic printing is critical. Also, the utilization of the dampening system complicates the press and its operation and adds to its initial cost.

The system utilised to apply the H2O solution to the plate surface is called the __________

The H2O solution utilised to prevent printing in the non-print areas is called the __________

The surface is treated with a __________ that is soaked into the image area, but avoided the H2O treated, non-image area.

___________MUST_BE_DESIGNED_ESPECIALLY_FOR_THIS_SYSTEM_TO_BE_EFFECTIVE;_THE_PRINCIPAL_DIFFERENCE_IS_THAT_THE____________VEHICLE_THAT‚ÄÖ√Ñ√∂‚ÀÖ√Ë‚ÀÖ¬•S_SELECTED_MUST_GIVE_SUITABLE_RHEOLOGICAL_PROPERTIES_SUCH_AS_A_FAIRLY_HIGH_VISCOSITY.?$#

Dot_gain_in_the_mid_tones_is_said_to_be_about____________lower_than_with_conventional_lithography.$

The __________ balance in offset lithographic printing is critical. Also, the utilization of the dampening system complicates the press and its operation and adds to its initial cost?

Most lithography is carried out as offset printing; the image on the ink plate is transferred to a rubber sheet and from the blanket to the paper.

The plate surface is often a thin __________ plate wrapped tightly around a cylinder. Every time the cylinder rotates, a copy can be made.

The system utilised to apply the H2O solution to the plate surface is called the __________

Laser printing method is sometimes called planographic printing since the image and non-image areas are in the same plane.

The H2O solution utilised to prevent printing in the non-print areas is called the __________

The surface is treated with a __________ that is soaked into the image area, but avoided the H2O treated, non-image area.

Lithography was invented by __________ in 1798.

Explore topic-wise MCQs in Pulp Paper.

Dot gain in the mid tones is said to be about __________ lower than with conventional lithography.

__________ must be designed especially for this system to be effective; the principal difference is that the __________ vehicle that’s selected must give suitable rheological properties such as a fairly high viscosity.

The __________ balance in offset lithographic printing is critical. Also, the utilization of the dampening system complicates the press and its operation and adds to its initial cost.

The system utilised to apply the H2O solution to the plate surface is called the __________

The H2O solution utilised to prevent printing in the non-print areas is called the __________

The surface is treated with a __________ that is soaked into the image area, but avoided the H2O treated, non-image area.

___________MUST_BE_DESIGNED_ESPECIALLY_FOR_THIS_SYSTEM_TO_BE_EFFECTIVE;_THE_PRINCIPAL_DIFFERENCE_IS_THAT_THE____________VEHICLE_THAT‚ÄÖ√Ñ√∂‚ÀÖ√Ë‚ÀÖ¬•S_SELECTED_MUST_GIVE_SUITABLE_RHEOLOGICAL_PROPERTIES_SUCH_AS_A_FAIRLY_HIGH_VISCOSITY.?$#

Dot_gain_in_the_mid_tones_is_said_to_be_about____________lower_than_with_conventional_lithography.$

The __________ balance in offset lithographic printing is critical. Also, the utilization of the dampening system complicates the press and its operation and adds to its initial cost?

Most lithography is carried out as offset printing; the image on the ink plate is transferred to a rubber sheet and from the blanket to the paper.

The plate surface is often a thin __________ plate wrapped tightly around a cylinder. Every time the cylinder rotates, a copy can be made.

The system utilised to apply the H2O solution to the plate surface is called the __________

Laser printing method is sometimes called planographic printing since the image and non-image areas are in the same plane.

The H2O solution utilised to prevent printing in the non-print areas is called the __________

The surface is treated with a __________ that is soaked into the image area, but avoided the H2O treated, non-image area.

Lithography was invented by __________ in 1798.

must be designed especially for this system to be effective; the principal difference is that the vehicle that’s selected must give suitable rheological properties such as a fairly high viscosity.