MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 17 Mcqs, each offering curated multiple-choice questions to sharpen your Machine Tools knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Which type of feed is needed in turning operation? |
| A. | longitudinal |
| B. | cross |
| C. | both cross and longitudinal |
| D. | none of the mentioned |
| Answer» B. cross | |
| 2. |
In taper operation, which type of surface is produced? |
| A. | flat |
| B. | curve |
| C. | circular |
| D. | none of the mentioned |
| Answer» E. | |
| 3. |
Traversing of tool at any angle to the job axis produces curve surfaces. |
| A. | true |
| B. | false |
| Answer» C. | |
| 4. |
Which type of surface is produced in facing operation? |
| A. | cylindrical |
| B. | taper |
| C. | flat |
| D. | none of the mentioned |
| Answer» D. none of the mentioned | |
| 5. |
TRAVERSING_OF_TOOL_AT_ANY_ANGLE_TO_THE_JOB_AXIS_PRODUCES_CURVE_SURFACES.?$ |
| A. | true |
| B. | false |
| Answer» C. | |
| 6. |
WHICH_TYPE_OF_SURFACE_IS_PRODUCED_IN_FACING_OPERATION??$ |
| A. | cylindrical |
| B. | taper |
| C. | flat |
| D. | none of the mentioned |
| Answer» D. none of the mentioned | |
| 7. |
Which type of feed is needed in turning operation?$ |
| A. | longitudinal |
| B. | cross |
| C. | both cross and longitudinal |
| D. | none of the mentioned |
| Answer» B. cross | |
| 8. |
In taper operation, which type of surface is produced?$ |
| A. | flat |
| B. | curve |
| C. | circular |
| D. | none of the mentioned |
| Answer» E. | |
| 9. |
Which type of surface can be produced by lathe? |
| A. | flat |
| B. | cylindrical |
| C. | curvilinear |
| D. | all of the mentioned |
| Answer» E. | |
| 10. |
Which type of feed is needed in facing operation? |
| A. | longitudinal |
| B. | cross |
| C. | both cross and longitudinal |
| D. | none of the mentioned |
| Answer» C. both cross and longitudinal | |
| 11. |
Lathe cannot produce internal features like holes. |
| A. | true |
| B. | false |
| Answer» C. | |
| 12. |
The swing diameter over the bed is the largest diameter. |
| A. | true |
| B. | false |
| Answer» B. false | |
| 13. |
Traversing of tool parallel to the axis of job is termed as_____ |
| A. | cross feed |
| B. | longitudinal feed |
| C. | both cross feed and traversing feed |
| D. | none of the mentioned |
| Answer» C. both cross feed and traversing feed | |
| 14. |
What is the necessary condition for turning? |
| A. | material of work piece should be harder than the cutting tool |
| B. | cutting tool should be harder than the material of work piece |
| C. | hardness of the cutting tool and material of of piece should be same |
| D. | none of the mentioned |
| Answer» C. hardness of the cutting tool and material of of piece should be same | |
| 15. |
Which type of surface is produced by turning operation in lathe machine? |
| A. | flat |
| B. | cylindrical |
| C. | taper |
| D. | none of the mentioned |
| Answer» C. taper | |
| 16. |
Lathe is primarily used for producing ____surfaces. |
| A. | flat |
| B. | curve |
| C. | taper |
| D. | none of the mentioned |
| Answer» E. | |
| 17. |
Which machine tool is known as the mother machine tool? |
| A. | drill |
| B. | milling |
| C. | lathe |
| D. | none of mentioned |
| Answer» D. none of mentioned | |