MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 17 Mcqs, each offering curated multiple-choice questions to sharpen your Advanced Machining knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
State whether the following statement is true or false regarding the limitations of ECM.“In electrochemical machining, duplicating the tool is easier.” |
| A. | True |
| B. | False |
| Answer» C. | |
| 2. |
State whether the following statement is true or false regarding the limitations of ECM.“In ECM, cleaning and oiling of work piece need not be done after machining.” |
| A. | True |
| B. | False |
| Answer» C. | |
| 3. |
Compared to other processes, machining is done at __________ voltages for high rates of material removal. |
| A. | Low |
| B. | Medium |
| C. | High |
| D. | very low |
| Answer» D. very low | |
| 4. |
HOW_ARE_MATERIAL_REMOVAL_RATES_OF_ECM,_WHEN_COMPARED_TO_THAT_OF_CONVENTIONAL_METHODS??$ |
| A. | Slower |
| B. | Faster |
| C. | Same |
| D. | None of the mentioned |
| Answer» B. Faster | |
| 5. |
Which of the following are the limitations of electro chemical machining?$ |
| A. | Removal of hydrogen |
| B. | Handling the electrolyte |
| C. | Energy consumption |
| D. | All of the mentioned |
| Answer» E. | |
| 6. |
Pumping of electrolyte through the narrow gaps causes, which type of forces on tool and work piece? |
| A. | Large |
| B. | Small |
| C. | Negligible |
| D. | No force |
| Answer» B. Small | |
| 7. |
Electro chemical machining process cannot produce which of the following mentioned below? |
| A. | Drilled holes |
| B. | Deburred edges |
| C. | Sharp edges |
| D. | All of the mentioned |
| Answer» D. All of the mentioned | |
| 8. |
State whether following statement is true or false regarding the limitations of ECM. |
| A. | |
| B. | True |
| Answer» C. | |
| 9. |
How much amount of energy is consumed in Electro chemical machining? |
| A. | Very small |
| B. | Small |
| C. | Medium |
| D. | Large |
| Answer» E. | |
| 10. |
What are the requirements of labour for machining purpose in Electrochemical machining? |
| A. | Low |
| B. | Medium |
| C. | High |
| D. | Very high |
| Answer» B. Medium | |
| 11. |
Which of the following materials can be machined using ECM? |
| A. | Hard nonconductive materials |
| B. | Hard conductive materials |
| C. | All nonconductive materials |
| D. | None of the mentioned |
| Answer» C. All nonconductive materials | |
| 12. |
How much amount of thermal damage occurs to the work piece? |
| A. | Small |
| B. | Large |
| C. | No thermal damage |
| D. | Negligible amount |
| Answer» D. Negligible amount | |
| 13. |
Complicated profiles can be machined in how many operations in Electrochemical machining? |
| A. | Single |
| B. | Double |
| C. | Triple |
| D. | Multiple |
| Answer» B. Double | |
| 14. |
Very small dimensions, up to which value can be controlled using ECM? |
| A. | 0.01 mm |
| B. | 0.05 mm |
| C. | 0.07 mm |
| D. | 0.12 mm |
| Answer» C. 0.07 mm | |
| 15. |
Compared to other processes, machining is done at _____ voltages for high rates of material removal. |
| A. | Low |
| B. | Medium |
| C. | High |
| D. | very low |
| Answer» D. very low | |
| 16. |
How much amount of wear is present in the tool used in Electrochemical machining? |
| A. | No wear |
| B. | Low |
| C. | Medium |
| D. | High |
| Answer» B. Low | |
| 17. |
What fraction of tool will always be in contact with the work piece? |
| A. | Half |
| B. | Full |
| C. | No contact |
| D. | Quarter |
| Answer» D. Quarter | |