MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 13 Mcqs, each offering curated multiple-choice questions to sharpen your Statistical Quality Control knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Length of a rectangular box is _______ |
| A. | a continuous measurement, i.e. a variable |
| B. | a discrete measurement, i.e. an attribute |
| C. | a continuous measurement, i.e. an attribute |
| D. | a discrete measurement, i.e. a variable |
| Answer» B. a discrete measurement, i.e. an attribute | |
| 2. |
Specifications are defined as ______ |
| A. | desired measurements of CTQ characteristics of whole product |
| B. | actual measurements of CTQ characteristic of whole product |
| C. | difference from desired measurements of CTQ characteristic of the components of product |
| D. | desired measurements of CTQ characteristics of the product components |
| Answer» E. | |
| 3. |
What does CTQ characteristic mean? |
| A. | Close to quality characteristic |
| B. | Comparison to quality characteristic |
| C. | Consumer to quality characteristic |
| D. | Critical to quality characteristic |
| Answer» E. | |
| 4. |
Which one of these is physical CTQ characteristic? |
| A. | Length |
| B. | Appearance |
| C. | Reliability |
| D. | Color |
| Answer» B. Appearance | |
| 5. |
Read the following sentences and choose the correct option.(i) Variables can only take discrete values while Attributes can take continuous values.(ii) Variables can only take continuous values while Attributes take discrete value.(iii) Attributes and variables are dependent on each other.(iv) Width of an impeller blade is a variable but no. of defective blades in a lot is an attribute. |
| A. | (i) and (iii) are correct |
| B. | (i)and (iii) are incorrect |
| C. | Only (i) is correct |
| D. | (i), (ii), (iii) and (iv) |
| Answer» C. Only (i) is correct | |
| 6. |
Quality characteristics are classified into variables and ________ |
| A. | constants |
| B. | attributes |
| C. | standards |
| D. | specifications |
| Answer» C. standards | |
| 7. |
Quality of a product is at its lowest when ____ quality component is neglected while it’s manufacturing. |
| A. | performance |
| B. | reliability |
| C. | aesthetics |
| D. | serviceability |
| Answer» B. reliability | |
| 8. |
What does reduced variability result in? |
| A. | Increased failure rate |
| B. | Decreased reliability |
| C. | Fewer repair claims |
| D. | Increased repair costs |
| Answer» D. Increased repair costs | |
| 9. |
How is the aesthetics of a product defined as? |
| A. | How good the product performs its job |
| B. | How good it looks |
| C. | How fast the job of the product is completed |
| D. | Whether the product is made exactly as the designer intended |
| Answer» C. How fast the job of the product is completed | |
| 10. |
Which one of these is not a component of quality? |
| A. | Reliability |
| B. | Durability |
| C. | Acceptance sampling |
| D. | Serviceability |
| Answer» D. Serviceability | |
| 11. |
Performance of a product is _____ |
| A. | how long the product lasts |
| B. | how easy it is to repair the product |
| C. | how often the product fails |
| D. | whether the product is capable of doing the intended job |
| Answer» E. | |
| 12. |
Which one of these is a dimension of quality? |
| A. | Performance |
| B. | Hazard rate |
| C. | Process Capability |
| D. | Control limits |
| Answer» B. Hazard rate | |
| 13. |
Quality is ______ variability. |
| A. | opposite of |
| B. | proportional to |
| C. | reciprocal of |
| D. | synonym of |
| Answer» D. synonym of | |