MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 440 Mcqs, each offering curated multiple-choice questions to sharpen your Textile Engineering knowledge and support exam preparation. Choose a topic below to get started.
| 351. |
Concentration of teeth in wiring is the |
| A. | number of teeth |
| B. | height of teeth |
| C. | size of teeth |
| D. | weight of teeth |
| Answer» B. height of teeth | |
| 352. |
Cotton laid is plucked in spinning process using |
| A. | Blender |
| B. | Tuft Plucker |
| C. | Drawn Sliver |
| D. | Bale Plucker |
| Answer» C. Drawn Sliver | |
| 353. |
Function of comber roller is to |
| A. | take up the material |
| B. | transfer fiber onto the drum |
| C. | cut the fiber |
| D. | retain material |
| Answer» B. transfer fiber onto the drum | |
| 354. |
In opening of tufts, fibers are |
| A. | stretched |
| B. | partially parallelized |
| C. | both a and b |
| D. | squeezed |
| Answer» D. squeezed | |
| 355. |
Variations in sliver count on card are highlighted by |
| A. | self counter |
| B. | self regulator |
| C. | both a and b |
| D. | none of above |
| Answer» C. both a and b | |
| 356. |
Simultaneous movement of knee and foot of needle allows distance between clothing to be |
| A. | variable |
| B. | constant |
| C. | increased |
| D. | decreased |
| Answer» C. increased | |
| 357. |
If wired element moves in same direction as that of teeth inclination than it is |
| A. | negative |
| B. | positive |
| C. | rotational |
| D. | horizontal |
| Answer» C. rotational | |
| 358. |
Blend has blades of different |
| A. | height |
| B. | size |
| C. | dimensions |
| D. | all of above |
| Answer» E. | |
| 359. |
Function of licker in knives is to eliminate |
| A. | impurities |
| B. | moisture |
| C. | particles |
| D. | fibers |
| Answer» B. moisture | |
| 360. |
Yarn fed to reeling machine is wounded on |
| A. | reel |
| B. | spindle |
| C. | rod |
| D. | cylinder |
| Answer» B. spindle | |
| 361. |
Each nozzle on oiling device sprays a jet of |
| A. | oil |
| B. | water |
| C. | chemical |
| D. | emulsion |
| Answer» E. | |
| 362. |
Apron is used for processing |
| A. | fine rovings |
| B. | extra fine rovings |
| C. | fine counts |
| D. | all of above |
| Answer» E. | |
| 363. |
Level of needles on flats is angular to drum. This angle is |
| A. | 1.0 degrees |
| B. | 1.5 degrees |
| C. | 2.0 degrees |
| D. | 2.5 degrees |
| Answer» C. 2.0 degrees | |
| 364. |
In straight rubber cot with elastic control, control greatly depends on |
| A. | condensation |
| B. | cross section of material and condensation |
| C. | condensation and liquefaction |
| D. | liquefaction |
| Answer» C. condensation and liquefaction | |
| 365. |
In automatic feeder, cleaner is no longer required and leveller is replaced by |
| A. | automatic leveller |
| B. | oscillating comb |
| C. | simple comb |
| D. | horizontal leveller |
| Answer» C. simple comb | |
| 366. |
Drum and worker cylinder rotates in |
| A. | same direction |
| B. | opposite direction |
| C. | parallel direction |
| D. | upward direction |
| Answer» C. parallel direction | |
| 367. |
Linker in cylinder in card rotates at a speed of |
| A. | 400 to 1,300 turns per min |
| B. | 1,400 to 1,600 turns per min |
| C. | 1,400 to 1,800 turns per min |
| D. | 1,800 to 2,000 turns per min |
| Answer» B. 1,400 to 1,600 turns per min | |
| 368. |
In double running process, travel of second range on rubbing point of first range must |
| A. | be reversed |
| B. | not be reversed |
| C. | be double |
| D. | not be double |
| Answer» C. be double | |
| 369. |
In bobbin formation, yarn tension increases during upward travel of |
| A. | ring |
| B. | ring rail |
| C. | bobbin |
| D. | yarn |
| Answer» C. bobbin | |
| 370. |
Card rotates at different speeds, effecting cardinal operations which are |
| A. | carding, stripping and raising |
| B. | carding and stripping |
| C. | stripping and raising |
| D. | carding, stripping and blending |
| Answer» B. carding and stripping | |
| 371. |
To prevent pills from opening, initial slashing should be |
| A. | thin |
| B. | swollen |
| C. | tight |
| D. | thick |
| Answer» E. | |
| 372. |
Malfile yarn can be obtained by using blend of long fibers having length greater than |
| A. | 10 mm |
| B. | 20 mm |
| C. | 40 mm |
| D. | 60 mm |
| Answer» D. 60 mm | |
| 373. |
Grill and knives on entry of Card machine is important for |
| A. | cleaning |
| B. | opening |
| C. | both a and b |
| D. | none of above |
| Answer» D. none of above | |
| 374. |
Rigid wiring in carding is for |
| A. | Rotating parts |
| B. | Mobile flats |
| C. | Fixed flats |
| D. | Rotating flats |
| Answer» B. Mobile flats | |
| 375. |
Maximum load in case of greater feeding load with proportional reduction of fibre count is calculated to be |
| A. | 8 g/m |
| B. | 15 g/m |
| C. | 20 g/m |
| D. | 25 g/m |
| Answer» C. 20 g/m | |
| 376. |
According to type of bale, their number ranges from |
| A. | 20 units to 80 units |
| B. | 80units to 100 units |
| C. | 10units to 20 units |
| D. | 100units to 140 units |
| Answer» B. 80units to 100 units | |
| 377. |
Drum speed of sliver count autoleveller is |
| A. | 150 to 300 rpm |
| B. | 300 to 450 rpm |
| C. | 450 to 600 rpm |
| D. | 600 to 750 rpm |
| Answer» C. 450 to 600 rpm | |
| 378. |
Beater cylinder is stripped with a |
| A. | round drum |
| B. | small drum |
| C. | large drum |
| D. | open ended drum |
| Answer» D. open ended drum | |
| 379. |
Single cylinder opener is designed for |
| A. | raw cotton |
| B. | saw ginned cotton |
| C. | roller cotton |
| D. | soft cotton |
| Answer» D. soft cotton | |
| 380. |
Fibers from same blend must posses |
| A. | same length |
| B. | different length same thickness |
| C. | different thickness |
| D. | same thickness |
| Answer» B. different length same thickness | |
| 381. |
In woolen spinning cycle, basic equipment is made up of |
| A. | breaker card, cross card and divider card |
| B. | cross card and divider card |
| C. | breaker and divider card |
| D. | None of the above |
| Answer» B. cross card and divider card | |
| 382. |
Apparatus used for technological analysis of a blend is |
| A. | Low Volume instrument |
| B. | Volume instrument |
| C. | High Volume instrument |
| D. | High tech instrument |
| Answer» D. High tech instrument | |
| 383. |
Beater opens fiber and arrange them in a |
| A. | sequential manner |
| B. | circular manner |
| C. | parallel manner |
| D. | regular manner |
| Answer» D. regular manner | |
| 384. |
What is number of parts card is divided into? |
| A. | 4 parts |
| B. | 3 parts |
| C. | 7 parts |
| D. | 8 parts |
| Answer» D. 8 parts | |
| 385. |
Card used in woolen spinning is covered with clothing that are |
| A. | at same level |
| B. | angular |
| C. | circular |
| D. | horizontal |
| Answer» C. circular | |
| 386. |
Control panel in aspiration cage controls the |
| A. | opening |
| B. | speed |
| C. | quantity of waste material |
| D. | all of above |
| Answer» E. | |
| 387. |
Weighing feeder can be fed |
| A. | automatically |
| B. | manually |
| C. | spontaneously |
| D. | mechanically |
| Answer» B. manually | |
| 388. |
Drum speed and defibration are |
| A. | directly proportional |
| B. | inversely proportional |
| C. | same |
| D. | different |
| Answer» B. inversely proportional | |
| 389. |
Material from breaker card is fed to intermediate card via |
| A. | conveyor belt |
| B. | condensation |
| C. | slip action |
| D. | rotatory cylinder |
| Answer» C. slip action | |
| 390. |
Fly cylinder has straight, long and flexible |
| A. | spikes |
| B. | needles |
| C. | rods |
| D. | bars |
| Answer» C. rods | |
| 391. |
Blend obtained from cotton helps in order to overcome shortcomings in supply of |
| A. | same type of cotton |
| B. | different type of cotton |
| C. | Raw cotton |
| D. | Processed cotton |
| Answer» B. different type of cotton | |
| 392. |
In carding room, number of cards is |
| A. | 2 |
| B. | 3 |
| C. | both a and b |
| D. | 5 |
| Answer» D. 5 | |
| 393. |
Size of teeth in carding is |
| A. | constant |
| B. | small |
| C. | large |
| D. | variable |
| Answer» E. | |
| 394. |
Only 'mobile' machine used in spinning is |
| A. | Tuft Plucker |
| B. | Blender |
| C. | Bale Plucker |
| D. | Drawn Sliver |
| Answer» B. Blender | |
| 395. |
Processing cycle of cotton used in a mill includes |
| A. | Carding |
| B. | Combing |
| C. | Open end |
| D. | all of above |
| Answer» E. | |
| 396. |
Opener cylinder posses diameter of |
| A. | 200 mm |
| B. | 300 mm |
| C. | 400 mm |
| D. | 500 mm |
| Answer» D. 500 mm | |
| 397. |
Entry cleaner cylinder rotates at a speed of |
| A. | 100 to 200 turns per min |
| B. | 200 to 400 turns per min |
| C. | 400 to 600 turns per min |
| D. | 600 to 800 turns per min |
| Answer» D. 600 to 800 turns per min | |
| 398. |
Types of card's clothing are |
| A. | flexible and inflexible |
| B. | sawtoothlike wire and flexible |
| C. | sawtoothlike wire and inflexible |
| D. | flexible wire and in flexible clothing |
| Answer» C. sawtoothlike wire and inflexible | |
| 399. |
According to layout of teeth, number of conditions possible for direction and speed of devices are |
| A. | 2 |
| B. | 3 |
| C. | 4 |
| D. | 5 |
| Answer» B. 3 | |
| 400. |
In carding room, number of working cylinders is |
| A. | upto 6 per drum |
| B. | upto 8 per drum |
| C. | upto 10 per drum |
| D. | upto 12 per drum |
| Answer» B. upto 8 per drum | |