MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 26 Mcqs, each offering curated multiple-choice questions to sharpen your Strength Materials knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
The time required for overtaking ___________ seconds. |
| A. | 9 to 14 |
| B. | 8 to 10 |
| C. | 11 to 15 |
| D. | 14 to 19 |
| Answer» B. 8 to 10 | |
| 2. |
In case of vertical curves, the ____________ are taken above the road. |
| A. | Gradient |
| B. | Super elevation |
| C. | Earth quantities |
| D. | Summit |
| Answer» D. Summit | |
| 3. |
According to IRC, the height of the object is taken to the height of ___________ mm. |
| A. | 200 mm |
| B. | 100 mm |
| C. | 450 mm |
| D. | 600 mm |
| Answer» C. 450 mm | |
| 4. |
Which of the following gradient is usually used in the construction of roads? |
| A. | Exceptional gradient |
| B. | Limiting gradient |
| C. | Hydraulic gradient |
| D. | Ruling gradient |
| Answer» E. | |
| 5. |
The longitudinal rise or fall off road surface along its length is _________ |
| A. | Camber |
| B. | Super elevation |
| C. | Gradient |
| D. | Carriage way |
| Answer» D. Carriage way | |
| 6. |
Stability of high rise vehicles will be affected due to ____________ |
| A. | Camber |
| B. | Gradient |
| C. | Super elevation |
| D. | Formation Width |
| Answer» B. Gradient | |
| 7. |
As per IRC, maximum width of lane considered as ____________ |
| A. | 2.44 m |
| B. | 2.35 m |
| C. | 3.5 m |
| D. | 3.4 m |
| Answer» B. 2.35 m | |
| 8. |
In cantilever beams, the maximum deflection occurs at ___________ |
| A. | Fixed end |
| B. | Free end |
| C. | Through out |
| D. | Point of loading |
| Answer» C. Through out | |
| 9. |
____________ is used to produce due to temperature variation in indeterminate structures. |
| A. | Stresses |
| B. | Strains |
| C. | Deflections |
| D. | Moment |
| Answer» B. Strains | |
| 10. |
Prop reduces ___________ in the beam. |
| A. | Deflection |
| B. | Slope |
| C. | Shear |
| D. | Moment |
| Answer» B. Slope | |
| 11. |
In cantilever beams, the extra support is known as ____________ |
| A. | Hinch |
| B. | Prop |
| C. | Cripple |
| D. | Indeterminate end |
| Answer» C. Cripple | |
| 12. |
THE_LONGITUDINAL_RISE_OR_FALL_OFF_ROAD_SURFACE_ALONG_ITS_LENGTH_IS__________?$ |
| A. | Camber |
| B. | Super elevation |
| C. | Gradient |
| D. | Carriage way |
| Answer» D. Carriage way | |
| 13. |
According to IRC, the height of the object is taken to the height of ___mm.$ |
| A. | 200 mm |
| B. | 100 mm |
| C. | 450 mm |
| D. | 600 mm |
| Answer» C. 450 mm | |
| 14. |
Which of the following gradient is usually used in construction of roads?$ |
| A. | Exceptional gradient |
| B. | Limiting gradient |
| C. | Hydraulic gradient |
| D. | Ruling gradient |
| Answer» E. | |
| 15. |
_____ provide gradual introduction of super elevation. |
| A. | Transition curves |
| B. | Summit curves |
| C. | Joint curves |
| D. | Adjoining curves |
| Answer» B. Summit curves | |
| 16. |
The time required for overtaking ___ seconds. |
| A. | 9 to 14 |
| B. | 8 to 10 |
| C. | 11 to 15 |
| D. | 14 to 19 |
| Answer» B. 8 to 10 | |
| 17. |
In case of vertical curves, the ____ are taken above the road. |
| A. | Gradient |
| B. | Super elevation |
| C. | Earth quantities |
| D. | Summit |
| Answer» D. Summit | |
| 18. |
What is the minimum shoulder width provided for village roads? |
| A. | 1.25 m |
| B. | 1.4 m |
| C. | 0.5 m |
| D. | 1 m |
| Answer» D. 1 m | |
| 19. |
Stability of high rise vehicles will be affected due to ___? |
| A. | Camber |
| B. | Gradient |
| C. | Super elevation |
| D. | Formation Width |
| Answer» B. Gradient | |
| 20. |
______ is the area of land acquired and reserved for future development. |
| A. | Right of pier |
| B. | Carriage way |
| C. | Right of way |
| D. | Camber |
| Answer» D. Camber | |
| 21. |
As per IRC, maximum width of lane considered as ____ |
| A. | 2.44 m |
| B. | 2.35 m |
| C. | 3.5 m |
| D. | 3.4 m |
| Answer» B. 2.35 m | |
| 22. |
In cantilever beams, the maximum deflection occurs at ____ |
| A. | Fixed end |
| B. | Free end |
| C. | Through out |
| D. | Point of loading |
| Answer» C. Through out | |
| 23. |
____ is used to produce due to temperature variation in indeterminate structures. |
| A. | Stresses |
| B. | Strains |
| C. | Deflections |
| D. | Moment |
| Answer» B. Strains | |
| 24. |
Which of the following is indeterminate structure? |
| A. | Singly rereinforced beam |
| B. | Propped cantilever beam |
| C. | Over hanging beam |
| D. | Simply supported beam |
| Answer» C. Over hanging beam | |
| 25. |
Prop reduces ___ in the beam. |
| A. | Deflection |
| B. | Slope |
| C. | Shear |
| D. | Moment |
| Answer» B. Slope | |
| 26. |
In cantilever beams, the extra support is known as ____ |
| A. | Hinch |
| B. | Prop |
| C. | Cripple |
| D. | Indeterminate end |
| Answer» C. Cripple | |