The differential energy equation for flow past a flat plate is given b

1.	The differential energy equation for flow past a flat plate is given by
A.	u d t/d x + v d t/d y = µ/p c (d u/d y)² + k d² t/p c d y²
B.	u d t/d x + v d t/d y = µ/p c (d u/d y) + k d² t/p c d y²
C.	u d t/d x + v d t/d y = k d² t/p c d y² + µ/p c (d u/d y)¯²
D.	u d t/d x + v d t/d y = µ/p c (d u/d y)¯¹ + k d² t/p c d y²
Answer» B. u d t/d x + v d t/d y = µ/p c (d u/d y) + k d² t/p c d y²

Discussion

No Comment Found

Related MCQs

Ambient air at 20 degree Celsius flows past a flat plate with a sharp leading edge at 3 m/s. The plate is heated uniformly throughout its entire length and is maintained at a surface temperature of 40 degree Celsius. Calculate the distance from the leading edge at which the flow in the boundary layer changes from laminar to turbulent conditions. Assume that transition occurs at a critical Reynolds number of 500000
The boundary layer thickness is taken to be at a distance from the plate surface to a point at which the velocity is given by
Air at 25 degree Celsius approaches a 0.9 m long and 0.6 m wide flat plate with a velocity 4.5 m/s. Let the plate is heated to a surface temperature of 135 degree Celsius. Find local heat transfer coefficient from the leading edge at a distance of 0.5 m
Air at 25 degree Celsius flows over a flat surface with a sharp leading edge at 1.5 m/s. Find the boundary layer thickness at 0.5 from the leading edge. For air at 25 degree Celsius, kinematic viscosity = 15.53* 10n¯⁶ m²/s
Boundary layer thickness is given by
A small thermo-couple is positioned in a thermal boundary layer near a flat plate past which water flows at 30 degree Celsius and 0.15 m/s. The plate is heated to a surface temperature of 50 degree Celsius and at the location of the probe, the thickness is 15 mm. The probe is well-represented byt – t S/t INFINITY – t S = 1.5 (y/δ) – 0.5 (y/δ)³Determine the heat transfer coefficient
During test-run, air flows at 215 m/s velocity and 25 degree Celsius temperature past a smooth thin model airfoil which can be idealized as a flat plate. If the chord length of the airfoil is 15 cm, find drag per unit width. The relevant physical properties of air arep = 1.82 kg/m³v = 15.53 * 10¯⁶ m²/s
A single pass shell and tube heat exchanger, consisting of a bundle of 100 tubes (inner diameter 25 mm and thickness 2 mm) is used for heating 28 kg/s of water from 25 degree Celsius to 75 degree Celsius with the help of a steam condensing at atmospheric pressure on the shell side with condensing heat transfer coefficient 5000 W/m² degree. Make calculation for overall heat transfer coefficient based on the inner area. Take fouling factor on the water side to be 0.002 m² degree/W per tube and neglect effect of fouling factor on the shell side and thermal resistance of the tube wall
Temperature and velocity profiles are identical when the dimensionless Prandtl number is
The assumptions for thermal boundary layer are(i) Steady compressible flow(ii) Negligible body forces, viscous heating and conduction in the flow direction(iii) Constant fluid properties evaluated at the film temperatureIdentify the correct option

The differential energy equation for flow past a flat plate is given by

Discussion

No Comment Found

Related MCQs

Reply to Comment