Match List-I with List-ll and select the correct answer using the code

Match List-I with List-ll and select the correct answer using the code given below the lists:
List-I List-II
A. Grashof number 1. Mass diffusion
B. Schmidt number 2. Transient heat conduction
C. Weber number 3. Free convection
D. Fourier number 4. Forced convection
5. Surface tension
6. Radiation

A - 4 , B - 2 , C - 3 , D - 5

A - 3 , B - 1 , C - 5 , D - 2

A - 5 , B - 1 , C - 2 , D - 4

A - 1 , B - 2 , C - 5 , D - 4

Answer» C. A - 5 , B - 1 , C - 2 , D - 4

Discussion

No Comment Found

Related MCQs

A fluid (Prandt/number, Pr = 1) at 500 K flows over a flat plate of 1.5 m length, maintained at 300 K. The velocity of the fluid is 10 m/s. Assuming kinematic viscosity. = 30 10 6 m /s, the thermal boundary layer thickness (in mm) at 0.5 m from the leading edge is ______.
A solid cylinder (surface 2) is located at the centre of a hollow sphere (surface 1). The diameter of the sphere is 1 m, while the cylinder has a diameter and length of 0.5 m each.'The radiation configuration factor F11 is
The properties of mercury at 300 K are: Density = 13529 kg/m , cp = 0.1393 kJ/kgK, dynamic viscosity = 0.1523 10 2 Ns/m and thermal conductivity = 8.540 W/mK. The Prandtl number of the mercury at 300 K is
Heat is generated uniformly in a long solid cylindrical rod (diameter =10 mm) at the rate of 4 107 W/m3. The thermal conductivity of the rod material is 25 W/mK. Under steady state conditions, the temperature ditference between the centre and the surface of the rod is 1 C.
A plane wall has a thermal conductivity of 1.15 W/mK. If the inner surface is at 1100 C and the outer surface is at 350 C, then the design thickness (in meter) of the wall to maintain a steady heat flux of 2500 W/m2 should be
A cylindrical uranium fuel rod of radius 5 mm in a nuclear is generating heat at the rate of 4 107 W/m3. The rod is cooled by a liquid (convective heat transfer coefficient 1000 W/ m2K) at 25 C. At steady state, the surface temperature (in K) of the rod is
A pipe of 25 mm outer diameter carries steam. The heat transfer coefficient between the cylinder and surroundings is 5 W/m2K. It is proposed to reduce the heat loss from the pipe by adding insulation having a thermal conductivity of 0.05 W/mK. Which one of the following statements is TRUE?
The ratios of the laminar hydrodynamic boundary layer thickness to thermal boundary layer thickness of flows of two fluids P and Q on a flat plate are 1/2 and 2 respectively. The Reynolds number based on the plate length for both the flows is 104. The Prandtl and Nusselt numbers for P are 1/8 and 35 respectively. The Prandlt and Nusselt numbers for Q are respectively
The total e-missive power of a surface is 500 W/ m2 at temperature T1 and 1200 W/m2 at temperature T2, where the temperature are in Kelvin. Assuming the e-missivity of the surface to be constant, the ratio of the temperature T1 /T2 is
If q"w = 5000 and the convection heat transfer coefficient at the pipe outlet is 1000 W/m2K, the temperature in C at the inner surface of the pipe at the outlet is

Match List-I with List-ll and select the correct answer using the code given below the lists: List-I List-II A. Grashof number 1. Mass diffusion B. Schmidt number 2. Transient heat conduction C. Weber number 3. Free convection D. Fourier number 4. Forced convection 5. Surface tension 6. Radiation

Discussion

No Comment Found

Related MCQs

Reply to Comment

Match List-I with List-ll and select the correct answer using the code given below the lists:
List-I List-II
A. Grashof number 1. Mass diffusion
B. Schmidt number 2. Transient heat conduction
C. Weber number 3. Free convection
D. Fourier number 4. Forced convection
5. Surface tension
6. Radiation